Publicité
MRP-F320
+
–
CH-2
SPEAKER
SUB W
OUTPUT
–
–
CH-4
–
(Rear side/Arrière/Parte trasera)
6
22
21
20
19
18
17
16
15
NOM
NOM
0.5V
0.5V
OFF
HP
OFF
MIN
MAX
MIN
MAX
(80Hz)
GAIN
GAIN
FILTER
CHANNEL-1/2
CHANNEL-3/4
(Front side/Avant/Parte delantera)
MRP-F200
–
CH-2
+
SPEAKER
OUTPUT
–
+
CH-4
–
BRIDGED
(Rear side/Arrière/Parte trasera)
22
21
20
19
18
17
16
15
NOM
NOM
0.5V
0.5V
OFF
HP
LP
MIN
MAX
MIN
MAX
(80Hz)
GAIN
GAIN
BASS BOOST
FILTER
CHANNEL-1/2
CHANNEL-3/4
(Front side/Avant/Parte delantera)
MRP-T130
–
BRIDGED
+
–
CH-2
SPEAKER
OUTPUT
(Rear side/Arrière/Parte trasera)
18
17
16
15
OFF
HP
LP
OFF
(80Hz)
BASS BOOST
FILTER
(Front side/Avant/Parte delantera)
+
–
CH-1
+
BATTERY REMOTE
GND
30A
POWER SUPPLY
+
+
–
CH-3
FUSE
BRIDGED
+
7
14
12
13
CH-1
CH-3
CH-1 2
3
4
NOM
100
0.5V
75
140
+
55
170
(L)
–
HP
OFF
ON
MIN
MAX
50
200
(80Hz)
INPUT
GAIN
BASS BOOST
LP FILTER
FILTER
SPEAKER
Sub woofer
(R)
LEVEL INPUT
CH-2
CH-4
–
CH-1
+
BATTERY REMOTE
GND
25A
POWER SUPPLY
–
+
CH-3
FUSE
+
6
7
14
11
12
13
CH-1+3
CH-1
CH-3
CH-1 2
3
4
+
(L)
–
OFF
ON
OFF
HP
LP
PRE
INPUT
(80Hz)
OUT
FILTER
SPEAKER
(R)
LEVEL INPUT
CH-2+4
CH-2
CH-4
+
+
BATTERY REMOTE
GND
–
CH-1
20A
POWER SUPPLY
FUSE
6
7
14
12
13
INPUT
CH-1 CH-2
NOM
0.5V
+
–
ON
MIN
MAX
GAIN
(L)
(R)
SPEAKER
LEVEL INPUT
CONNECTIONS (Fig. 3 – Fig. 13)
Before making connections, be sure to turn the
power off to all audio components. Connect the
yellow battery lead from the amp directly to the
positive (+) terminal of the vehicle's battery. Do
not connect this lead to the fuse block.
To prevent external noise from entering the
audio system.
• Locate the unit and route the leads at least 10
cm away from the car harness.
8
• Keep the battery power leads as far away
from other leads as possible.
9
• Connect the ground lead securely to a bare
10
metal spot (remove the coating if necessary)
of the car chassis.
• If you add an optional noise suppressor,
connect it as far away from the unit as
possible. Your Alpine dealer carries various
Alpine noise suppressors, contact them for
further information.
• Your Alpine dealer knows best about noise
prevention measures so consult your dealer
for further information.
Speaker Output Terminal
6
The MRP-F320/MRP-F200/MRP-T130 has two
sets of speaker outputs. Be sure to observe
correct speaker output connections and phasing.
In the stereo mode, connect the right speaker
outputs to the right speaker and the left to left.
Connect the positive output to the positive
speaker terminal and the negative to negative.
In the bridged mode, connect the left positive to
the positive terminal on the speaker and the
8
right negative to the negative terminal of the
speaker. Do not use the speaker (–) terminals as
9
a common lead between the left and right
10
channels. Do not connect this lead to the
vehicle's chassis.
NOTES:
1. Do not connect speaker leads together or to
chassis ground.
2. In case of bridge connection, use Y-adaptor
(sold separately). (Refer to the "Bridge
Connections" below.)
Insulation Tube
7
Use for POWER SUPPLY (BATTERY/REMOTE/
GND) and SPEAKER OUTPUT terminals.
Ground Lead (Black) (Sold Separately)
8
Connect this lead securely to a clean, bare
metal spot on the vehicle's chassis. Verify this
point to be a true ground by checking for
continuity between that point and the negative
(–) terminal of the vehicle's battery. Ground all
your audio components to the same point on the
chassis to prevent ground loops.
8
9
10
Fig. 3
Remote Turn-On Lead (Blue/White) (Sold
9
Separately)
Connect this lead to the remote turn-on or power
antenna (positive trigger, (+) 12V only) lead of
your head unit.
Battery Lead (Yellow) (Sold Separately)
10
Be sure to add a
30 amp fuse as close as
possible to the battery's positive (+) terminal.
This fuse will protect your vehicle's electrical
system in case of a short circuit. If you need to
extend this lead, the wire gauge should be 8
AWG or larger.
MRP-F320 ... 30 amp fuse
MRP-F200 ... 25 amp fuse
MRP-T130 ... 20 amp fuse
Pre-Out Jacks (MRP-F200 only)
11
These jacks provide a Front + Rear summed
output (Non-fading ). This is an ideal output for
driving a separate subwoofer amp. This output is
full-range, and is not affected by the crossover.
RCA Input Jacks
12
Connect these jacks to the line out leads on your
head unit using RCA extension cables (sold
separately). Be sure to observe correct channel
connections; Left to Left and Right to Right.
(Front to Front and Rear to Rear (except for
MRP-T130))
Speaker Level Input Connector
13
These leads are input leads for use with head
units not equipped with preamp outputs. When
not using the RCA Line Input connectors, you
should connect these wires to the speaker
output leads of your head unit. The MRP-F320/
MRP-F200/MRP-T130 accepts input from high
power or standard power head units.
Speaker Input Leads
14
These leads are input leads for use with head
units not equipped with preamp outputs.
Connect these wires to the speaker output leads
of your head unit. The MRP-F320/MRP-F200/
MRP-T130 accepts input from high power or
standard power head units.
Front Left Speaker (White (+))
15
Front Left Speaker (White/Black (–))
16
Front Right Speaker (Gray (+))
17
Front Right Speaker (Gray/Black (–))
18
Rear Left Speaker (Green (+))
19
(except for MRP-T130)
Rear Left Speaker (Green/Black (–))
20
(except for MRP-T130)
Rear Right Speaker (Violet (+))
21
(except for MRP-T130)
Rear Right Speaker (Violet/Black (–))
22
(except for MRP-T130)
Publicité
