Philips SENSOTOUCH 3D RQ1290 Mode D'emploi page 9

Masquer les pouces Voir aussi pour SENSOTOUCH 3D RQ1290:
Table des Matières

Publicité

trimming
You can use the trimmer to groom your sideburns and moustache.
1
Pull the shaving unit straight off the shaver (Fig. 23).
Note: Do not turn the shaving unit while you pull it off the shaver.
2
Press the on/off button once to switch on the shaver.
The display lights up for a few seconds.
,
3
Press the trimmer slide forwards to slide out the trimmer (Fig. 24).
4
You can now start trimming.
5
Press the trimmer slide backwards to retract the trimmer.
6
Press the on/off button once to switch off the shaver.
The display lights up for a few seconds and shows the remaining battery capacity.
,
7
Insert the lug of the shaving unit into the slot in the top of the shaver (1). Then press the shaving unit downwards (2) to attach it to the
shaver ('click') (Fig. 25).
cleaning and maintenance
Never use scouring pads, abrasive cleaning agents or aggressive liquids such as petrol or acetone to clean the shaver and the Jet Clean
System (specific types only).
-
The best and most hygienic way to clean the shaver is in the Jet Clean System (specific types only). You can also rinse the shaver under the
tap or clean it with the cleaning brush supplied.
-
Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt.
-
Clean the shaver after every shave for optimal shaving performance.
-
You can clean the outside of the shaver with a damp cloth.
-
Regular cleaning guarantees better shaving performance.
cleaning the shaving unit
Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt.
1
Rinse the shaving unit under a hot tap for some time (Fig. 26).
2
Pull open the three shaving heads one by one (Fig. 27).
3
Rinse all three shaving heads and all three hair chambers under a hot tap for 30 seconds. (Fig. 28)
Note: You can also brush the shaving heads and hair chambers with the cleaning brush supplied.
Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt.
4
Carefully shake off excess water and leave the shaving heads open to let the shaving unit dry completely.
Never dry the shaving unit with a towel or tissue, as this may damage the shaving heads.
cleaning the shaving unit in the Jet clean system (specific types only)
The Jet Clean system comes in two types:
-
Type RQ1008 has three cleaning programs: the eco program, the auto program and the intensive program. Press the up/down button to
select the cleaning program you prefer. (Fig. 29)
Note: The eco program has a shorter drying time, to save energy. The intensive program is a more thorough cleaning program.
-
Type RQ1007 has one automatic cleaning program. When you press the on/off button, the Jet Clean System starts cleaning in the
automatic cleaning program. (Fig. 30)
preparing the Jet clean system for use
Fill the cleaning chamber before first use.
1
Put the small plug in the Jet Clean System.
2
Put the adapter in the wall socket.
The holder automatically moves to the highest position.
,
3
Simultaneously press the release buttons on both sides of the cleaning chamber (1). Then lift the Jet Clean System off the cleaning
chamber (2). (Fig. 31)
The cleaning chamber remains behind.
,
4
Unscrew the cap from the bottle with cleaning fluid.
5
Fill the cleaning chamber with HQ200 cleaning fluid to a level between the two lines (Fig. 32).
6
Place the Jet Clean System back onto the cleaning chamber (Fig. 33).
Make sure the release buttons click back into place.
using the Jet clean system
Note: If you use the shaver with shaving foam or shaving gel, we advise you to rinse it under the hot tap before you clean it in the Jet Clean System. This
guarantees an optimal lifetime for the cleaning fluid.
1
Press the shaver tightly into the holder to lock it into place.
The display shows that the shaver is charging (see chapter 'The display').
,
2
RQ1008: Press the up/down button to select a cleaning program.
3
Press the on/off button on the Jet Clean System to start the cleaning program. (Fig. 34)
English
9

Publicité

Table des Matières
loading

Table des Matières