Replacing The Bulb In The Oven Ceiling Light; Glass Cover; After-Sales Service; E Number And Fd Number - Junker JH11AA Série Mode D'emploi

ã=
Risk of electric shock!
Repairs that are not carried out properly are dangerous.
Repairs must only be performed by one of our after-sales
service technicians.

Replacing the bulb in the oven ceiling light

If the bulb in the oven light fails, it must be replaced. Heat-
resistant, 25 watt spare bulbs can be obtained from our after-
sales service or a specialist retailer. Only use these bulbs.
ã=
Risk of electric shock!
Switch off the circuit breaker in the fuse box.
Place a tea towel in the cold oven to prevent damage.
1.
Unscrew the glass cover by turning it anti-clockwise.
2.

After-sales service

Our after-sales service is there for you if your appliance needs
to be repaired. We will always find the right solution in order to
avoid unnecessary visits from a service technician.

E number and FD number

When calling us, please give the product number (E no.) and
the production number (FD no.) so that we can provide you with
the correct advice. The rating plate containing these numbers is
found on the side of the oven door. To save time, you can make
a note of the number of your appliance and the telephone
number of the after-sales service in the space below, should it
be required.

Energy and environment tips

Here you can find tips on how to save energy when baking and
roasting and how to dispose of your appliance properly.

Saving energy

Only preheat the oven if this is specified in the recipe or in
■
the tables in the instruction manual.
Use dark, black lacquered or enamelled baking tins, because
■
they absorb heat particularly well.
Open the oven door as infrequently as possible while the
■
food is baking and roasting.
If you intend to bake several cakes, preferably bake them one
■
after the other. The oven is still hot. Because the oven is still
hot from the previous cake, the baking time for the next cake
is reduced. You can also place two fruit loaf tins next to each
other in the oven.
For longer cooking times, you can switch the oven to the
■
minimum temperature 10 minutes before the end of the
cooking time. At the end of the cooking time, take out the
cooked food and switch off the function selector and
temperature selector. The appliance is now switched off.
Note:
To prevent moisture from forming on the control panel, do not
leave the cooked food in the appliance.
32
Replace the bulb with one of the same type.
3.
Screw the glass cover back in.
4.
Remove the tea towel and switch on the circuit breaker.
5.

Glass cover

You must replace a damaged glass cover. Suitable glass
covers may be obtained from the after-sales service. Please
specify the E number and FD number of your appliance.
E no.
After-sales service O
Please note that there will be a fee for a visit by a service
technician in the event of a malfunction, even during the
warranty period.
After-sales contact details for all countries can be found in the
attached after-sales service directory.

Environmentally-friendly disposal

Dispose of packaging in an environmentally-friendly manner.
This appliance complies with European Directive
2002/96/EC on Waste Electrical and Electronic
Equipment (WEEE). The directive gives a framework for
the collection and recycling of old appliances, which is
valid across the EU.

Measures to be noted during transport

Secure all mobile parts in and on the appliance using an
adhesive tape that can be removed without leaving any traces.
Push all accessories (e.g. baking tray) into the corresponding
slots with cardboard at the edges, in order to avoid damaging
the appliance. Place cardboard or similar between the front and
rear side to prevent knocks against the inside of the door glass.
Secure the oven door to the side walls of the appliance using
adhesive tape.
Keep the original appliance packaging. Only transport the
appliance in the original packaging. Observe the transport
arrows on the packaging.
FD no.