Pioneer DEH-4200SD Mode D'emploi page 16

Section
02 Operating this unit
FM step (FM tuning step)
Normally the FM tuning step employed by seek tuning
is 50 kHz. When AF or TA is on, the tuning step auto-
matically changes to 100 kHz. It may be preferable to
set the tuning step to 50 kHz when AF is on.
1 Press M.C. to display the setting mode.
2 Turn M.C. to select the FM tuning step.
100kHz (100 kHz)—50kHz (50 kHz)
3 Press M.C. to confirm the selection.
Auto PI (auto PI seek)
The unit can automatically search for a different sta-
tion with the same programming, even during preset
recall.
1 Press M.C. to turn Auto PI seek on or off.
AUX (auxiliary input)
Activate this setting when using auxiliary device con-
nected to this unit.
1 Press M.C. to turn AUX on or off.
USB PnP (plug and play)
This setting allows you to switch your source to USB/
USB-iPod automatically.
1 Press M.C. to turn the plug and play on or off.
ON – When USB storage device/iPod is con-
nected, the source is automatically switched to
USB/USB-iPod. If you disconnect your USB sto-
rage device/iPod, this unit's source is turned off.
OFF – When USB storage device/iPod is con-
nected, the source is not switched to USB/USB-
iPod automatically. Please change the source to
USB/USB-iPod manually.
Brightness (display brightness setting)
1 Press M.C. to display the setting mode.
2 Turn M.C. to switch the brightness setting.
High (high)—Low (low)
3 Press M.C. to confirm the selection.
SW control (rear output and subwoofer setting)
Only for DEH-4200SD.
This unit's rear output (rear speaker leads output) can
be used for full-range speaker (Full) or subwoofer
(SUBW) connection. If you switch the rear output set-
ting to SUBW, you can connect a rear speaker lead di-
rectly to a subwoofer without using an auxiliary amp.
1 Press M.C. to display the setting mode.
2 Turn M.C. to change the setting.
Rear SP: Full—SUBW
3 Press M.C. to confirm the selection.
16
En
Only for DEH-3200UB.
The rear speaker leads output (Rear SP) and RCA out-
put (Preout) of DEH-3200UB can be used for full-
range speaker (Rear SP :Full/Preout :Rear) or sub-
woofer (Rear SP :SUBW/Preout :SUBW) connection.
If you switch to Rear SP :SUBW, you can connect a
rear speaker lead directly to a subwoofer without
using an auxiliary amp.
Initially, Rear SP is set for rear full-range speaker con-
nection (Full). When Rear SP :Full is selected, you can
connect the RCA output to a subwoofer. In this case,
you can select whether to use the subwoofer control-
ler's (low pass filter, phase) built-in Preout :SUBW or
the auxiliary Preout :Rear.
1 Press M.C. to display the setting mode.
2 Press M.C. to cycle between as following:
Rear SP/Preout—Full (SUBW)/SUBW(Rear)
3 Turn M.C. to change the setting.
Rear SP: Full—SUBW
Preout: SUBW—Rear
! Even if you change this setting, there is no
output unless you turn the subwoofer output
on (refer to SW setting 1 (subwoofer on/off
setting) on page 14).
! If you change this setting, subwoofer output
in the audio menu will return to the factory
settings.
4 Press M.C. to confirm the selection.
DEMO (demo display setting)
1 Press M.C. tp turn the demo display on or off.
Ever SCRL (scroll mode setting)
When Ever Scroll is set to ON, recorded text informa-
tion scrolls continuously in the display. Set to OFF if
you prefer the information to scroll just once.
1 Press M.C. to turn the ever scroll on or off.
Title (multi language)
This unit can display them even if they are embedded
in a European language or Russian.
Text information such as title name, artist name or
comment can be recorded on a compressed audio
disc.
! If the embedded language and the selected lan-
guage setting are not the same, text information
may not be displayed properly.
! Some characters may not be displayed properly.
1 Press M.C. to display the setting mode.
2 Turn M.C. to select the desired setting.
EURO (European)—RUSSIA (Russian)
3 Press M.C. to confirm the selection.