Publicité
Les langues disponibles
Les langues disponibles
O 5001 / OXI1408T
FINGERTIP PULSE OXIMETER WITH TEMPERATURE
Warning: Please read this instruction manual carefully before using the instrument and keep
it for future use.
A.
SAFETY INSTRUCTIONS
-
The device is intended exclusively for private and not for commercial use. Only use this
device as describe in this instruction manual.
-
Never try to repair it by yourself. It must be repaired by the manufacturer or its service agent
or a similarly qualified person in order to avoid an electric shock.
-
Keep it away from heat sources such as radiators, to avoid deformation of plastic parts.
-
Do not use coarse or abrasive sponges/cloths or steel wool to clean the appliance.
-
Do not attempt to service the Fingertip Pulse Oximeter. Only qualified service personnel
-
should attempt any needed internal servicing.
-
Do not use the pulse oximeter in situations where alarms are required .The device has
-
no alarms.
-
Prolonged use or the patient's condition may require changing the sensor site periodically.
-
Change sensor site and check skin integrity, circulatory status and correct alignment at
-
least every 2 hours.
-
SpO2 measurements may be adversely affected in the presence of high ambient light.
-
Shield the sensor area
(with a surgical towel, or direct sunlight, for example) if
-
necessary.
-
The following reason will cause interference and defibrillators
(1)High-frequency electrosurgical.
(2)Placement of a sensor on an extremity with a blood pressure cuff arterial catheter, or
intravascular line.
(3)The patient has hypotension severe vasoconstriction severe anemia or hypothermia.
(4)The patient is in cardiac arrest or is in shock.
(5)Fingernail polish or false fingernails may cause inaccurate SpO2 readings.
Warnings
-
WARNING: EXPLOSION HAZARD — Do not use the Oximeter in a flammable
atmosphere where concentrations of flammable anesthetics or other materials may occur.
-
WARNING: Do not throw batteries in fire as this may causes them to explode.
-
WARNING: Do not attempt to recharge normal dry-cell batteries, they may leak, And may
cause a fire or even explode.
EN
-
WARNING: Do not use the pulse oximeter in an MRI or CT environment.
-
CAUTION: Keep the operating environment free of dust, vibrations, corrosive, or
flammable materials, and extremes of temperature and humidity.
-
CAUTION: Do not operate the unit if it is damp or wet because of condensation or spills.
-
Avoid using the equipment immediately after moving it from a cold environment to a warm,
humid location.
-
CAUTION: Never use sharp or pointed objects to operate the front-panel switches.
-
CAUTION: The battery must be taken out from the battery compartment if the device will
not be used for a long time.
-
CAUTION: The device shall only be used if the battery cover is closed.
-
CAUTION: The battery must be proper disposed according to local regulation after their use.
B.
HOW TO USE IT
1)
Insert or replace batteries
- Remove the battery cover on the back of the unit.
- Insert 2 AAA batteries observing the correct polarity indicated.
- Replace the cover.
2)
Operation
Turn the Pulse Oximeter on/off
Put one of fingers into rubber hole of the Oximeter (it is best to put the finger thoroughly)
with nail surface upward, then releasing the clamp.
Press power button to turn the Pulse Oximeter on. The oximeter will automatically be
powered off when no finger in the device for longer than 16 Seconds
Read correspondent data from display screen.
The display interface of "OLED" can rotate four directions with six different display modes
after pressing the power button for less than 0.5s.It is shown as below:
Note: when battery power is at lowest level, the battery capacity indicates symbol of
"in OLED, remind users of replacement of battery.
TEMPERATURE FUNCTION
When the oximeter is off, press the ON / OFF button for at least 3 seconds until a small beep sounds.
Place the oximeter in front of your forehead, making sure your fingers are not on the sensor. Wait a few
seconds.
A new beep is emitted when the temperature measurement is completed. You can then read the result on
the LCD screen. The display is in degrees Celsius and in degrees fahrenheit.
The display turns off automatically after 3 seconds.
C.
CARE AND MAINTENANCE
*Switch off the power and take out the batteries before cleaning. Keep the exterior surface
of the device clean and free of dust and dirt. Cleaning exterior surface (OLED display
screen included) of the unit with a dry and soft cloth. Use 75% density of medical alcohol
to clean the surface and use dry fabric with little alcohol to avoid alcohol permeates into
Publicité
