Ryobi PSP02 Manuel D'utilisation page 8

Masquer les pouces Voir aussi pour PSP02:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

WARNING:
Do not allow conductive or corrosive fluids to get inside
the battery pack. If conductive or corrosive fluids are
spilled on the battery, refer to the instructions in your
battery operators manual.
NOTICE:
Remove tank and fill away from sprayer. Clean the exterior
of the tank and clean up any spillage before replacing
tank.
When adding spray solutions, you may add water and the
desired chemical solution directly into the tank, or use a
solution that has been premixed in a separate container,
then poured into the sprayer, using a funnel if needed. For
either method, remember:
 Liquids used must be as thin as water. Thicker liquids will
not spray properly.
 Do not overfill the tank.
NOTE: If using a measuring container or funnel to fill the
tank, be sure to thoroughly clean and rinse these items after
use. If premixing the spraying solution, rinse the container
used for mixing.
To fill:
 Turn electrostatic function off and remove the battery
from the unit.
 Place sprayer with tank on a flat surface.
 Unlock the latches securing the tank to the sprayer.
 Lift the sprayer off the tank.
 Unscrew the cap and remove it from the tank.
 Fill the tank with the desired amount of liquid (up to
33.8 oz.).
NOTE: To ensure proper operation of the sprayer, do
not fill past the 1 L line.
 Screw the cap back onto the tank, making sure it is
tightened securely.
NOTE: Wipe the outside of the tank with a dry cloth and
clean up any spills before installing the tank.
 Place tank on flat surface.
 Place sprayer on top of tank.
 Lock the latches to secure the tank in place.
 Reinstall the battery pack.
OPERATION
NOTICE:
It is important to thoroughly clean the unit after each use.
Allowing liquid to remain in an idle tool for an extended
period may cause its moving pieces and connectors to
seize up.
INSTALLING/REMOVING BATTERY PACK
See Figure 6, page 14.
 Insert the battery pack into the product as shown.
 Make sure the latches on each side of the battery pack
snap in place and the battery pack is secured in the
product before beginning operation.
 Turn electrostatic function off before removing the battery
from the unit
 Depress the latches to remove the battery pack.
For complete charging instructions, see the operator's manu-
als for your battery pack and charger.
LED WORKLIGHT
See Figure 7, page 14.
The built-in LED worklight is convenient when working in
close or tight areas where additional light is needed. When-
ever the switch trigger is depressed, the LED worklight will
illuminate.
TURNING THE SPRAYER ON/OFF
See Figure 7, page 14.
 To turn the sprayer ON, depress the switch trigger.
 To turn the sprayer OFF, release the switch trigger.
USING THE ELECTROSTATIC FUNCTION
See Figures 8 - 9, page 14.
This sprayer can be used with or without electrostatic charg-
ing. When the electrostatic feature is turned off, the droplets
in the spray will remain inside the spray area until they are
absorbed or wiped away. When the electrostatic feature is
turned on, the droplets in the spray are given a positive elec-
trical charge. Each charged droplet adheres to the surface
being sprayed while simultaneously repelling and spreading
apart from one another. As the droplets spread apart, they
will expand beyond the spray area and cover more of the
target surface. The droplets will maintain their distance until
they are absorbed or wiped away.
NOTE: Turn the electrostatic feature off, if you want to
concentrate a large amount of spray in a small area. Turn the
electrostatic feature on, if you want to evenly apply product
over a large area.
To activate electrostatic mode:
 Slide switch located on top of unit to ON position.
To deactivate electrostatic mode:
 Slide switch located on top of unit to OFF position.
8 – English

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Psp02k

Table des Matières