Dimas TS 180E Manuel D'utilisation page 9

This symbol indicates that the
machine is in conformance with
the applicable European directive.
MANDATORY
WARNING
These signs give advice
concerning your safety
Instruction plate
MANUFACTURER
TYPE TYPE N° SERIE
ANNEE DE
FABRICATION
WEIGHT MASSE UTILE Kg PUISSANCE
PLAGE DE
MAXI TOOL Ø MAXI OUTIL. mm
TENSION
BORE Ø ALESAGE mm FREQUENCE
SPEED T/MN - RPM INT. UTIL.
1 Utilisation
• Utilisation : Water-cooled cutting of tile
materials.
• Blade with continuous rim Ø 180 mm (D)
bore Øx25,4 mm (AL).
Use only continuous rim diamand
blades.
• Cutting thickness (material) :
to 90° : 34 mm - to 45° : 20 mm
• Cutting width (Lg) with guide at 90° :
170 mm
• Length of cut unlimited.
2 Technical features
• Power : 0,8 KW
• Voltage : 230 V - 50 Hz
• Motor speed : 2800 rpm
• Dimensions (mm) l x w x h :
- 425 x 380 x 240
• Weight : 10 kg
• Blade cooling by partial immersion
• Tank capacity: 1,5 litres (autonomy 10 minu-
tes cutting)
• Power cable : HO5 VVF 3 x 0.75 mm
1,50 m.
• Use coefficient : 15% (10mn/h)
POWER PRESSURE
MODEL
LEVEL LEVEL
Lwa (dB) Lpa (dB)
EN ISO 3744 EN ISO 4871
0.8 KW 230 V 74 68
3
Pre-use check-list
Before use, read the instructions
INDICATION
carefully and familiarise yourself
INFORMATION
with the machine.
INSTRUCTION
The working area must be per-
PROHIBITION
fectly tidy, well lit and must offer
no risks (no humidity or dange-
rous products in the vicinity).
The operator must wear
suitable protection when
working.
SERIAL
FABRICATION
YEAR
Any unauthorised persons must
kW POWER
be kept away from the working
V VOLTAGE
Hz FREQUENCY
area.
A INTENSITY
Use blades suitable for the work
to be done (speed, geometry,
application, etc.)
4 Electrical connections
- ELECTRICAL SAFETY :
Operate this machine only on a
supply equipped with a 30 mA ear-
thed current-limiting circuit-brea-
ker. Otherwise, consult our catalo-
gue for appropriate models.
- The RCCB must be used cor-
rectly, including testing it regu-
larly. For tools supplied with an
integral RCCB in the cable or in
the mains plug, if the cable or
plug
repairs must be carried out by
the manufacturer, one of his
agents or by a qualified repair
workshop to avoid any risks
resulting from errors.
- Check the mains voltage is iden-
tical to that shown on the instruc-
tion plate N on the machine
2
[FIG.x1]
- length
- Use twin & earth plugs S.T.D. 3
pin plug 240 V.
- Extension cable : cable section
adequate for the electric power,
VIBRATION
LEVEL
connection to the main by a type
HO7 RNF cable of 2.5 mm
G
ENV 25349
tion up to 50 m.
0.08
•Disconnect the machine.
•Remove the disk covers (A)and(B).
•Remove the water bath (C).
•Unscrew the tightening nut right-hand
•Remove the outer flange (E). The blade is
•Fit the diamond blade.
• Check correct centring of the blade.
• Replace the outer flange and lock the nut.
• Replace the disk housing
•Check that the disk is centred.
has been damaged,
• Fill the water bath.
• Connect the machine to the mains.
2 sec-
• Start by means of the on-off switch
5 Fitting the blade
thread(D).
tightened by hand, or use a spanner as
appropriate.
Rotation direction is indicated by
an arrow on one side of the
blade.
Make sure the contact faces of
flanges, of blade and the axle are
clean
6 Starting up
Always take care.
Get into a comfortable, balanced
position.
Remove all adjustment tools and
wrenches from floor and machi-
ne
Keep the protective covers in
place while the machine is opera-
ting.
I
.
7