Asist AE7AF120IN18 Mode D'emploi page 35

AddiTiOnAL SAFETY inSTRUcTiOnS
Before using this device, make sure that you have
read and understood all the instructions that apply
to this device. Failure to follow these instructions
may result in personal injury and increase the risk of
electric shock. Please check that all accessories used
in this device or replaced parts are properly and / or
securely fastened in the device. Please keep these
instructions for future reference.
NOTICE!!
The device complies with the safety regulations requi-
red for electrical equipment.
Please read the operating instructions before using
the device.
Improper use can lead to personal injury and property
damage. People who are not familiar with the instruc-
tions cannot use the device. Keep these instructions
in a safe place for future reference.
Children and adolescents are not allowed to work with
the device.
Safety information
! Do not leave the vacuum cleaner switched on una-
ttended.
! The supply voltage must be as indicated on the
rating plate.
! Do not clean the vacuum cleaner with the mains
cable. Unplug the cable from the mains socket. Pro-
tect the power cord from oil, heat and sharp corners.
A damaged cord can cause an electric shock.
! Make sure that the cable is not damaged, eg by
running over, crushing, tearing, etc.
! If the cord is damaged during operation, unplug the
power cord immediately.
DO NOT TOUCH THE CABLE UNTIL IT IS DISCO-
NNECTED FROM THE SUPPLY VOLTAGE.
! If the supply cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
! Disconnect the vacuum cleaner from the power
supply when not in use or to be modified.
! Keep the nozzle and filters clean to ensure that the
vacuum cleaner works well and safely.
! Do not leave the vacuum cleaner outside in the rain.
! Do not use the vacuum cleaner to vacuum flamma-
ble or explosive liquids, corrosive objects, hot and
burning dust and substances harmful to the human
body.
! Make sure that the ash temperature does not exce-
ed 50 ° C.
! Use only accessories recommended by the manu-
facturer.
! Store the vacuum cleaner in a dry room.
- Use protective equipment against noise, dust and
vibration !!!
SAVE THESE SAFETY INSTRUCTIONS !!!
dEScRiPTiOn ( A )
This ash vacuum cleaner has been designed exclu-
sively for vacuuming cold ash. It is not suitable for
boilers and oil stoves or for gypsum or cement dust.
1) Power switch
2) Handle
3) Air inlet
4) Vacuum cleaner container (case)
5) Suction tube
6) Engine cover
7) HEPA filter
8) Air outlet
Dust knob button
Pictograms
Pictograms on the product packaging:
a) Power supply values
b) Power consumption
c) Volume of collection container: 18L
USE And OPERATiOn
ASIST tools are intended for home or hobby use only.
The manufacturer and importer do not recommend
using this tool in extreme conditions and under high
loads.
Any additional requirements must be the subject of
an agreement between the manufacturer and the
customer.
Always remove the mains plug from the socket before
working on the device.
Vacuum cleaner installation
Remove the vacuum cleaner from the packaging. Re-
lease the clamps and remove the main (motor) part
from the housing. Then check the accessories and
that the casing of the device is in good condition.
- Attach the washable filter to the lower base of the
motor, after prolonged use the filter should be remo-
ved and the dust wiped off with a brush.
- Firmly connect the vacuum cleaner inlet connector
and the aluminum tube (5) to both ends of the metal
hose (3).
- To vacuum the ashes, place the aluminum tube in
the fireplace or in the stove.
- Plug in the power cord
- Switching on: set the ON / OFF switch to „I"
- Off: set the ON / OFF switch to „0"
- Slowly and evenly move the aluminum suction hose
over the dirty surface.
Install the HEPA filter as shown in the following figure
and screw it on.
Attention!! The rubber part of the HEPA filter must
touch the red fuse switch, otherwise the vacuum
cleaner semotor
will not start.
35