System Reset; Backlight; Warranty; Specifications - PERFECTPRO SOLID DIGITAL Manuel De L'utilisateur

Press the Tuning knob to view the software version.
5.
6. Press the Tuning knob to back to last menu and press menu to return to the normal
radio display.

SYSTEM RESET

If the radio fails to operate correctly, or some digits on the display are missing or
incomplete, carry out the following procedure.
1. Press the On/Off button to switch on the radio.
2. Press the Menu button,
3. Rotate the Tuning knob until the display shows "System". Press the Tuning knob.
4. Rotate the Tuning knob until the display shows "Factory reset". Press the Tuning knob.
5. Rotate the Tuning knob to select between "Yes" or "No". Select "Yes" if you wish to
reset the radio, otherwise, select "No".
6. Press the Tuning knob to cause the factory reset.
7. A full reset will be performed. All presets and the station list will be erased. All
settings will be set to the default values. The display will show "WELCOME TO
DIGITAL RADIO" for a few seconds, and then the radio will automatically perform
an auto scan of the Band III DAB channels and the FM band, the display will show
"Scanning" at DAB and "Auto" at FM.
In case of malfunction due to electrostatic discharge; reset the product as above to
resume normal operation. If you are not able to perform the reset operation as above,
remove and reconnect all batteries and the power supply.
INFORMATION ON THE METAL TELESCOPIC ANTENNA
The antenna placed on this radio is a long, metal telescopic antenna.
This antenna is NOT flexible or bendable and should be used with care.
When used in a dusty or dirty environment please clean the antenna from time to
time with a dry cloth to ensure normal operation. When used in a wet, moist or dirty
environment it is advised to regularly, after first cleaning with a dry cloth, thinly apply a
universal protection oil (like e.g. WD40) with a cloth to prevent rust and corrosion and to
ensure normal operation.
ADDITIONAL FLEXIBLE PLASTIC ANTENNA (SUPPLIED WITH THE RADIO IN THE
BOX)
You can use this as an alternative antenna for your radio in a situation where the metal
telescopic antenna is too vulnerable.
Installing: Carefully screw off the standard metal telescopic antenna. First carefully
loosen the
antenna with an open-end-wrench (size 14) – turn counter anti-clockwise.
Carefully screw on the flexible plastic antenna and softly tighten it with an open-end
wrench key (size 14) – turn clockwise.
ATTENTION: In order to prevent the antennas' thread from breaking off or being
damaged do not over-tighten antennas with the spanner.
13

BACKLIGHT

LCD backlight configuration
1. Press the On/Off button to turn on the radio.
Press the Menu button, and then rotate the Tuning knob until the display shows
2.
"LCD backlight".
3. Press the Tuning knob to enter the LCD backlight adjustment menu.
4. Rotate the Tuning knob to select "on" in order to keep backlight always lightened
when the radio is turned on with AC power supply;
5. Or rotate the Tuning knob to select "off" (by default) so that the backlight will be
lightened for about 10 seconds whenever a button is pressed with AC power supply.
6. Press the Tuning knob to confirm your choice.

WARRANTY

This radio has a 2 year limited warranty.
WARNING ! Warranty becomes void once the radio cabinet has been opened or
any modifications or alterations to the radio have been made !
The terms of the warranty of this radio do not cover the following:
- Damage caused by misuse, abuse, neglect, alterations, accidents or unauthorised
repair.
- Normal wear and tear.
- Breaking or bending of the metal telescopic antenna

SPECIFICATIONS

Power requirements
Mains AC230V ~, 50Hz
Frequency coverage
DAB 174,928 – 239,200 MHz
FM 87.5 – 108 MHz
Circuit features
Loudspeaker 1 x ø4 inch
Output power 1 x 5w
Aux In socket ø3.5 mm
Environmental note
This product has been manufactured with high quality parts and
materials, which can be reused and recycled.
Therefore, do not throw the product away with normal household
waste at the end of its service life. Take it to a collection point for the
recycling of electrical and electronic device. This is indicated by this
symbol on the product, in the operating manual and on the packaging.
Please find out about collection points operated by your local authority.
Help protect the environment by recycling used products.
GB
G B
14