Power Supply; Using The Radio For The First Time; Dab Radio Mode - PERFECTPRO SOLID DIGITAL Manuel De L'utilisateur

POWER SUPPLY

AC operation
1. Before plugging the AC power cord into the AC socket, be sure the voltage is
correct.
2. AC power cord storage is designed to store the cord when the radio is not in use.
Note:
In order to disconnect the unit from the mains completely, the AC power cord should be
removed from the mains socket completely.
In case of malfunction due to electrostatic discharge or fast transient (burst), remove
and reconnect the power supply.

USING THE RADIO FOR THE FIRST TIME

1. Place the radio on a flat surface.
2. Carefully extend the telescopic antenna located on the top of the radio.
Adjust the antenna so it is vertically extending above the radio.
3. Plug the AC power cord into the AC socket. The radio will start up and the radio will
automatically perform an auto scan of the Band III DAB channels and the FM band.
The display will show "Scanning" in DAB and "Auto" in FM.
4. When the scan is completed, the 10 strongest FM stations will be stored as presets
and the available DAB stations will be in the list of stations. The radio will switch to
standby with the updated clock and date showing on the display.

DAB RADIO MODE

Operating the radio – DAB
1. Carefully extend the telescopic antenna located on the top of the radio.
Adjust the antenna so it is vertically extending above the radio. Press the On/Off
button to switch on the radio.
Select the DAB waveband by pressing the Source button.
2.
3. The first station in the list of stations found will be played. The display will show
the station name. If the radio has been used before, the last used station will be
selected.
4. If no DAB signals are detected, "No stations available" will be displayed. It may
be necessary to relocate the radio to a position with better reception. You should
then carry out an auto scan to find stations, please refer to the section "Find new
stations - DAB".
5
Selecting a station – DAB
1. Press the On/Off button to switch on the radio. The display will show "Connecting"
and "Playing" for a few seconds.
2. The display shows the name of the radio station currently selected.
3. Rotate the Tuning knob to scroll through the list of available stations.
4. When the desired station name appears on the display, press the Tuning knob to
select the station.
Note: If after selecting a station the display shows "No stations available", it may be
necessary to relocate the radio to a position with better reception.
Display modes – DAB
In DAB mode, the radio can display a range of information on the display.
Press the Info button to cycle through the various modes.
a. Scrolling text Displays scrolling text message e.g. station information,
artist/track name, phone-in number, etc.
b. Signal strength Displays the signal strength of radio reception. The clear
unfilled rectangle indicates minimum signal level required
for satisfactory reception.
c. Program type Displays the type of station being listened to e.g. Pop,
Classic, News, etc.
d. Multiplex name Displays the name of multiplex to which the current
station belongs.
e. Channel & frequency Displays the channel number and frequency for the
currently tuned DAB station.
f. Bit rate & audio format Displays the digital audio bit rate and audio format.
g. Time & date Displays the current time and date.
Finding new stations – DAB
From time to time, new stations may become available. You may proceed to find new
stations as follows:
1. In DAB mode, press the Menu button, "Full scan" shows on the display.
2. Press the Tuning knob, the radio will perform a scan of the Band III DAB channels.
As new stations are found, the station counter on the right-hand side of the display
will increase and new radio stations found will be added to the list stored in the radio.
Manual Tuning – DAB
Manual tuning is an alternative method of finding new stations. Instead of scanning the
entire Band III channels automatically, you may tune the radio directly to a known DAB
channel and store all the multiplex in that channel into the available station list.
1. In DAB mode, press the Menu button and rotate the Tuning knob until the LCD
display shows "Manual Tune", then press the Tuning knob. The display will show
DAB channel and Frequency.
GB
G B
6