Publicité
Les langues disponibles
Les langues disponibles
ENGLISH
SPECIFICATIONS
Max. cutting capacities
Maximum dado capacity
No load speed (RPM)
Table size (W x L)
Dimensions (L x W x H)
• Due to our continuing programme of research and development, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
For Your Own Safety Read Instruc-
tion Manual Before Operating Tool
Save it for future reference
GENERAL SAFETY PRECAUTIONS
(For All Tools)
1.
KNOW YOUR POWER TOOL. Read the owner's
manual carefully. Learn the tool's applications
and limitations, as well as the specific potential
hazards peculiar to it.
2.
KEEP GUARDS IN PLACE and in working order.
3.
REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking to see that keys and
adjusting wrenches are removed from tool
before turning it on.
4.
KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
5.
DON'T USE IN DANGEROUS ENVIRONMENT.
Don't use power tools in damp or wet locations,
or expose them to rain. Keep work area well
lighted. Don't use tool in presence of flammable
liquids or gases.
6.
KEEP CHILDREN AWAY. All visitors should be
kept safe distance from work area.
7.
MAKE WORKSHOP KID PROOF with padlocks,
master switches, or by removing starter keys.
8.
DON'T FORCE TOOL. It will do the job better and
safer at the rate for which it was designed.
9.
USE RIGHT TOOL. Don't force tool or attachment
to do a job for which it was not designed.
Model
Arbor hole
Blade diameter
90°
45°
Net weight
2702 / 2702X1
210 mm (8-1/4")
68 mm (2-11/16")
47 mm (1-3/4")
560 mm x 686 mm x 458 mm (22" x 27" x 18")
10. WEAR PROPER APPAREL. Do not wear loose
clothing, gloves, neckties, rings, bracelets, or
other jewelry which may get caught in moving
parts. Nonslip footwear is recommended. Wear
protective hair covering to contain long hair.
11. ALWAYS USE SAFETY GLASSES. Also use face
or dust mask if cutting operation is dusty. Every-
USA007-2
day eyeglasses only have impact resistant
lenses, they are NOT safety glasses.
12. SECURE WORK. Use clamps or a vise to hold
work when practical. It's safer than using your
hand and it frees both hands to operate tool.
13. DON'T OVERREACH. Keep proper footing and
balance at all times.
14. MAINTAIN TOOLS WITH CARE. Keep tools sharp
and clean for best and safest performance. Fol-
low instructions for lubricating and changing
accessories.
15. DISCONNECT TOOLS before servicing; when
changing accessories such as blades, bits, cut-
ters, and the like.
16. REDUCE THE RISK OF UNINTENTIONAL START-
ING. Make sure switch is in off position before
plugging in.
17. USE RECOMMENDED ACCESSORIES. Consult
the owner's manual for recommended accesso-
ries. The use of improper accessories may cause
risk of injury to persons.
18. NEVER STAND ON TOOL. Serious injury could
occur if the tool is tipped or if the cutting tool is
unintentionally contacted.
19. CHECK DAMAGED PARTS. Before further use of
the tool, a guard or other part that is damaged
should be carefully checked to determine that it
2
2703 / 2703X1
5/8"
255 mm (10")
91 mm (3-9/16")
63 mm (2-1/2")
13 mm (1/2")
4,600/min.
686 mm x 560 mm (27" x 22")
18 kg (40 lbs)
Publicité
