Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
•
Check that the pump drain hose does not
link or block.
•
Empty the water of the bucket.
•
Reinstall the pump hose if it drops and
reinstall the bucket properly. Turn on the
unit. if the error repeats, call for service.
Do not use this operation when the outdoor
temperature is equal to or less than 0°C (32°F),
otherwise water is become ice that will cause
the water hose blocked up and the unit failure.
Make sure to empty the bucket once a week
when using the pump draining feature. When
the pump draining feature is not being used,
remove the pump drain hose from the outlet.
Press the pump drain hose outlet in and take
the pump drain hose out from it (see Fig.6).
Make sure do not let the water in the pump
hose drip to the floor.
CAre AND MAINTeNANCe
Care and cleaning of the dehumidifier
•
Before any operation, unplug the device
•
Empty the water from the tank and rinse
off with clear water. if needed, use a soft
detergent.
•
Check if the back vent is not dusty. if
needed, clean it with a dry brush or a
vacuum.
•
Do not splash the device. if needed, use
a wet cloth.
•
Filters cleaning:
-
Clean the filter with warm soapy water.
-
Rinse and let the filter dry before
replacing it.
Storage
•
When not using the unit for a long time,
after turning off the unit, wait a day
before emptying the tank.
•
Clean with a white vinegar based solution.
•
Let the device dry.
•
Store in a dry place, preferably in its original
packaging. Avoid high temperatures.
16
5. Cleaning the filter of the pump.
1. Push
2. Pull
6. Removing the drain pump hose
Precautions
•
Check that the device is not swamped.
•
Do not use bleach or abrasives to
wash the device. Use water and mild
detergent.
•
Do not use the appliance outdoor.
•
Place the device on a hard surface.
•
The
device
is
suitable
for
use
temperatures between 5 and 35°C.
•
Allow at least 20 cm of space on all sides
of the unit for good air circulation.
•
Do not connect the dehumidifier to a
multiple socket outlet, which is also being
used for other electrical appliances.
•
Plug the unit to an electrical socket with
earth connection.
•
The dehumidifier must be operated in an
enclosed area to be more effective.
The product does not work properly
Situation
The unit does not start.
The dehumidifier does not dry
the air as it should.
The device makes a loud
noise when operating.
Frost appears on the coils.
at
Water on the floor.
AS, ES, P2; EC, E3, Eb
messages appears on the
display.
Solution
Make sure the dehumidifier's plug is pushed
completely into the socket.
Check the house circuit breaker.
Dehumidifier has reached its preset level or the tank
is full.
Tank is not in the proper position.
Allow enough time for the moisture to be absorbed.
Make sure there are no curtains, blinds or furniture
blocking the front or back of the dehumidifier.
Make sure the unit is not too close to a wall.
The humidity control may not be set low enough.
Check that all doors, windows and other openings
are securely closed.
Room temperature is too low, below 5°C.
There is a kerosene heater or a vapor generating
appliance in the room.
The air filter is clogged.
The unit is tilted instead of upright as it should be.
The floor surface is not level.
This is normal. The dehumidifier has an auto defrost
feature. Make sure the ambient temperature is higher
than 5°C.
The hose connection may be loose.
Tighten connections.
These are error codes and protection codes. See the
"Control panel description"
⑨
section.
17
Publicité
Table des Matières
