Ac Power Input; Basic Operation; Standby Switch; Dvd Power Switch - Rotel RDV-1080 Manuel De L'utilisateur

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

RDV-1080 DVD Audio/Video Player

AC Power Input

It is best to plug the RDV-1080 directly into a
2-pin polarized wall outlet. Avoid the use of
extension cords.
Your RDV-1080 will automatically configure
itself for the proper AC line voltage ranging
from 110 volts to 240 volts at 50/60Hz. No
setting is required to match the unit to your
local voltage.
Plug the supplied cord into the AC INPUT re-
ceptacle on the back of the unit. After all con-
nections have been made, plug the cord into
an appropriate AC wall outlet.
: If you are away from home for an ex-
NOTE
tended period of time, it is a sensible precau-
tion to unplug your audio/video components.

Basic Operation

The RDV-1080 can be operated using its front-
panel buttons or from corresponding buttons
on the supplied infrared remote control. Spe-
cific instructions for each of the basic operat-
ing controls are detailed here. Additional fea-
tures, as well as settings available from the
On-Screen Displays are described in later
sections of the manual.

STANDBY Switch

DVD POWER Switch

Standby LED

The LED above the front-panel STANDBY but-
ton illuminates when the RDV-1080 is connected
to a live AC outlet, but is in standby mode.
Press the STANDBY button or remote control
DVD POWER button to fully activate the
RDV-1080, indicated by the front-panel dis-
play being illuminated. Press either button again
to put the RDV-1080 in standby mode; the dis-
play turns off and the LED illuminates.
Pressing the OPN/CLOSE button or PLAY
will also activate the unit from standby mode.
: You can choose to use an Auto Standby
NOTE
function that puts the unit in standby mode
after 30 or 60 minutes of inactivity. See the
Setting Preferences section of this manual.
Front-Panel Display
DISPLAY OFF Button
A lighted display on the front-panel of the
RDV-1080 provides information about the status
of the unit, activation of special features, and
track/time information.
The display can be turned off by pressing the
DISPLAY OFF button which will light the LED
above the button. Press the button again to
turn the display back on.
See the illustration at the front of this manual
for the location of each section of the display:
Title/Group
displays the number of the
current Title or Group .
Chapter/Track
displays the number of
the current Chapter or Track .
Step
displays the current step number of
the program.
Audio Format
displays the digital au-
dio format of the inserted disc.
B.S.P./Bonus
indicates when a DVD
Audio disc contains B.S.P. (Browsable Still Pic-
tures) or a Bonus Group.
Disc Type
displays the type of disc in-
serted in the unit.
Function
indicates which special features
are activated.
Time Mode
indicates which time mode
is shown in the Multi-Information Window of
the Display.
Audio Channel
shows which of the six
possible audio channels are in use.
Multi-Information
shows time and status
information in an alphanumeric display.

Audio LED Indicators

Five front-panel LEDs provide information about
the format of the disc being played.
DVD Audio
lights when the disc contains
DVD Audio programming.
Sampling Rate
indicates the sampling
frequency of the digital bitstream
16
Disc Drawer
OPN/CLOSE Button
A motor-driven disc drawer, located in the
center of the RDV-1080, slides out to accept
a disc and retracts for playback. Place the disc
in the drawer label-side up. Make sure the disc
is properly centered in the tray. Do not use
accessory stabilizer devices.
When the disc drawer is closed, pressing the
OPN/CLOSE button opens the drawer. Press
the button again to close the drawer. The
drawer also closes when the PLAY
is pressed.
In addition, the drawer can also be closed from
the opening On-Screen Display by moving the
cursor over the CLOSE icon and pressing the
ENTER button on the remote.
Playing a Disc
PLAY/SELECT Buttons
Press the PLAY
button to start playing the
disc from the beginning. If the disc drawer is
open, it will close automatically.
The PLAY
button always starts play from the
beginning of the disc, except when it is after
the PAUSE
button has been pressed. In this
case, the disc will resume playing from the
current location.
Playback can also be started from the Open-
ing Screen Display by moving the cursor over
the PLAY icon and pressing the ENTER button
on the remote.
Stopping a Disc
STOP/CLEAR Buttons
Press the STOP
button to stop a disc that is
playing. Playback will also stop when the DVD
POWER button on the remote is pressed.
The RDV-1080 memorizes the point at which
the disc stopped playing, with an option of
resuming play at that point (see RESUME but-
ton, following). This stored position remains
in memory even if the unit is put in standby
mode; however, it is erased from memory when
the disc drawer is opened.
Resuming Play
RESUME Button
The RESUME button restarts playback after it
has been stopped. Instead of playing from the
start of the disc, the RESUME button restarts
play at the last location on the disc when play
was stopped.
English
button

Publicité

Chapitres

Table des Matières
loading

Table des Matières