Information For Operation; Cleaning, Maintenance And Ordering Of Spare Parts - HERKULES SHZ 500-2 Mode D'emploi D'origine

Anleitung_SHZ_500_2_SPK7:_
GB
All screws must be tightened correctly. A qualified
technician should check the anchoring of the arm
before the machine is started.
6.3 Block and tackle function (Fig. 6 – 9)
The cable hoist is fitted with a return roller (15) and
an additional hook (16). If these parts are used
correctly, the cable hoist can lift twice its rated load.
Fit the return roller (15) and additional hook (16) as
shown in Figure 6 – 8. The permanent hook (8) must
be attached to the fastening hole (2) (Fig. 9).
The load is now raised by two steel cables, which
means that the cable hoist can lift twice its rated
load.
7. Operation

7.1 Information for operation

1. Remove the adhesive tape from the drum (3)
before using the hoist for the first time.
2. The value of the A-rated noise emissions at the
operatorʼs position is less than 70 dB
(determined in accordance with EN ISO 11201).
3. Supply voltage: 230 V ± 10%, 50 Hz ± 1%.
4. The cable hoist must be operated in ambient
temperatures of between 0°C and 40°C with a
relative humidity of less than 85%. Height above
sea level: max. 1,000 m.
5. The temperature for transport and storage may
be between -25°C and 55°C. The maximum
temperature must not exceed 70°C.
6. The user should lift the load off the ground at the
slowest possible speed. The cable should be taut
when the load is raised.
7. The motor (14) for the cable hoist is fitted with a
thermostat switch. Whilst the cable hoist is
operating, the motor (14) may therefore stop. It
will restart automatically when it has cooled
down.
8. The electric cable hoist is not fitted with a rated
power limiter. You should therefore not repeat
attempts to lift a load if the overload trip is
limiting the hoistʼs operation. In this case the load
exceeds the rated capacity of the cable hoist.
9. Do not leave any suspended loads unsupervised
without first taking the appropriate safety
precautions.
10. Fit the machine with a 10 A fuse or a 10 A
residual current operated circuit breaker (RCCB)
to protect the circuit
11. Do not use the lever (4/5) as a routine stopping
device. It should only be used to stop the
machine in an emergency.
12
06.04.2010 8:32 Uhr Seite 12
12. Before you start, ensure that the steel cable (6)
is correctly wound around the drum (3) and that
the spacing between the windings is smaller than
the steel cable (Fig. 3)
13. Ensure that the load is correctly secured to the
hook (8) or, if you are using the block and tackle,
the additional hook (16) and always maintain a
safe distance from the load and the steel cable
(6).
7.2 Operation (Fig. 9)
Check whether the Emergency Stop switch (9) is
pressed. Turn the red stop switch clockwise to
release it.
Press the pushbutton ▲ (10) to raise the load.
Press the pushbutton ▼ (10) to lower the load.
Automatic stop mechanism lever (5): When the
maximum lifting height has been reached, the
cut-out weight (7) presses the lever (5) upwards.
This trips a limit switch after which the load
cannot be raised any further.
Lever for maximum cable length (4): When the
load has reached its lowest possible position, a
limit switch is tripped which makes it impossible
to lower the load any further. This limit switch
also prevents the cable hoist operating in the
wrong direction (hook moving in the opposite
direction to the arrow shown on the control
switch).
The cable hoist will stop if the Emergency Stop
switch (9) is pressed.
In an emergency, immediately press the
Emergency Stop switch (9) to stop the cable
hoist. The cable hoist cannot be operated if the
Emergency Stop switch has been pressed.
8. Cleaning, maintenance and
ordering of spare parts
Always pull out the mains power plug before starting
any cleaning work.
8.1 Cleaning
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
We recommend that you clean the device
immediately each time you have finished using it.
Clean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts of
the equipment. Ensure that no water can seep
into the device.