Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
EN
The electric line must be exclusively reserved for the mo-
torisation and equipped with protection, comprising:
• a 10 A fuse or breaker,
• a differential type device (30 mA).
An all-pole power supply cut-off device must be provid-
ed. The switches provided to ensure a cut-out of all poles
on fixed appliances must be connected to the power sup-
ply terminals and there must a separation between the
contacts on all poles to ensure complete disconnection
in conditions where category III high impulse voltage is
present.
It is recommended that you fit a lightning conductor
(maximum residual voltage 2 kV).
1.5.1. Cable feed
DANGER
Underground cables must be equipped with a protective
sheath with a sufficient diameter to contain the motor ca-
ble and the accessories cables.
Low-voltage cables subject to inclement weather must
be at least of type H07RN-F.
For overground cables, use a cable grommet that will
withstand the weight of vehicles (ref. 2400484).
1.6. Clothing precautions
Take off any jewellery (bracelet, chain, etc.) during installation.
For manoeuvring, drilling and welding operations, wear ap-
propriate protection (special glasses, gloves, ear protection,
etc.).
1.7. Safety instructions relating to installation
DANGER
Do not connect the motorisation to a power source before
installation is complete.
WARNING
Modifying any of the components in this kit or using ad-
ditional components not recommended in this manual is
strictly prohibited.
Monitor the gate as it moves and keep people away from it
until installation is complete.
Do not use adhesive to secure the motorisation.
WARNING
Take care when using the manual unlocking device. Man-
ual unlocking may result in uncontrolled movement of
the gate.
ATTENTION
Install any fixed control device at a height of at least 1.5
m and within sight of the gate, but away from moving
parts.
A er installation, ensure that:
• the mechanism is correctly adjusted
• the manual back release device is operating correctly
• the motorisation changes direction when the gate encoun-
ters an object 50 mm high positioned halfway up the leaf.
3
1.8. Safety devices
DANGER
It is mandatory to install an active safety edge with auto-
test function in order for the installation to be compliant.
WARNING
For operation in automatic mode or remote control, pho-
toelectric cells must be installed.
The automatic motorisation operates in at least one di-
rection with no intentional activation by the user.
For operation in automatic mode, or if the gate faces a public
road, installation of an orange light may be required in accord-
ance with the regulations in the country in which the motori-
sation is installed.
1.9. Regulations
Somfy declares that, when used in accordance with these
instructions, the product described in these instructions
complies with the essential requirements of the applicable
European Directives, and in particular Machinery Directive
2006/42/EC and Radio Equipment Directive 2014/53/EU. The
full text of the EC declaration of conformity is available on the
following website: www.somfy.com/ce. Antoine CREZE, Head
of Regulations, Cluses
1.10. Assistance
You may encounter difficulties or have questions when install-
ing your motorisation.
Do not hesitate to contact us; our specialists are on hand to
answer all your questions.
Internet: www.somfy.com
2. PRODUCT DESCRIPTION
2.1. Field of application
This motorisation is intended exclusively for installation with a sliding gate
for residential use weighing a maximum of 2,000 kg and no more than 20
m long.
2.2. Composition of the kit - Fig. 1
No.
Qty
1
1
RTS ELIXO 2000 230V motor
Mounting kit:
2
1
Metal plate
3
16
nut
4
4
Lag screws
5
2
End limit brackets
6
4
Bar
7
2
Cable clamp
8
4
Cable clamp bolt
9
2
Key
10
2
Remote control*
* The model and number of remote controls may vary depending on the pack.
ELIXO 2000 230V RTS
Description
Copyright
©
2018 SOMFY ACTIVITES SA. All rights reserved.
Publicité
Chapitres
Table des Matières
Dépannage
