Installation; User's Instructions - IGEA 2400 Mode D'emploi

C.B.M. S.r.l. Medical Equipment - Via Castello 10, 26038 Torre dé Picenardi (CR) - Italy
UTILITY key:
When it is pressed it enables the access to the utility
functions.
SHIFT key:
If it is pressed together with the RESET or
COUNTER keys, it enables their working.
Manometer:
During the sterilization phase a pressure is created in
the chamber.
In the Maintenance section controls to be effected
are signalled.
Serial outlet:
The writing printer identifies the serial outlet SR2
through which it is possible to connect the sterilizer
with a PC or with a printer in order to carry out the
recording of the sterilization cycles.
Access to the reservoir
In the upper part of the equipment it is possible to
enter the reservoir, for its filling or its possible topping
up. We recommend to let the reservoir always closed
during the use of the autoclave.
We deeply recommend the use of distilled water in
order to avoid scalings in the machine that could
compromise its functionality.
Access to the chamber
Access to the sterilization chamber is made up of a
handwheel and a safety hook.
inside the chamber keep the safety hook raised, and
screw up the handwheel anticlockwise.
Thanks to the safety hook, it is not possible to enter
the sterilization chamber when the equipment is
working. This in order to prevent the unintentional
opening of the autoclave with the consequent risk of
not effecting the sterilization or to damage things
and/or people. We recommend never to force the
lever in order to open the chamber, in this case wait
for some seconds and try to open again.
Chamber drain cock
If you open the door, placed on the right part of the
sterilizer, you approach the drain cock of the water
from the chamber, useful in case of malfunction.
Clutch to unload the water tank
By opening the autoclave door the proper tube can
be connected with the clutch for unloading the water
tank.
Please remember that the other end of the tube shall
be first put into a vessel to collect unloaded water.

INSTALLATION

Place the autoclave on a solid and strong plane. With
the help of a level, check the setting on the plane of
the sterilizer. If a regulation is necessary release the
nuts placed under the autoclave through a 13 mm.
key and unscrew or screw the feet until the optimal
positioning is reached, then lock the nuts.
Electric system connection
Connect up the power supply cable to the apparatus
and turn on the main switch
Rev. 7 – 24/07/2006
Connect the equipment to an electric plug equipped
with an earthing, with a feeding voltage of 230Volt.
and with a minimum capacity of 10A.
On the autoclave safety fuses of the kind 250V - 10A
- 5x20 are installed.
USER' S INSTRUCTIONS
Even if it is equipped with multifunction push
buttons the autoclave can be used in a very
simple way through the following keys:
START
CYCLE
DRYING
ATTENTION: we recommend to clean and dry
carefully the material to sterilize.
For a simple and essential use of the autoclave
operate in the following way:
•
Press the main switch and check the water level.
‚
In case the water is missing, remove the reservoir lid
and directly pour the distilled water into the opening
until the FULL yellow led lights up (maximum level)
or at least the OK green led, then close again the
reservoir.
In order to enter
ƒ
Insert the material to sterilize into the chamber and
close again, turning the handwheel clockwise.
After the lightening of the door locked led effect
again
„
Press the CYCLE key and select the cycle to effect.
IMPORTANT: Before selecting the cycle check the
table at page 15 and verify the compatibility of the
material to sterilize with the temperature and the kind
of cycle.
...
Press the DRYING key in order to select the possible
drying (see table at page 15 ).
†
After
correspondence of the effected choices press
START and verify the lighting of the cycle led.
The writing CYCLE N°x will appear on the display,
and from this moment the autoclave shall begin the
sterilization phases in a completely automatic mode.
‡
It is possible to follow all the sterilization phases
reading them on the display.
ˆ
At the end of the cycle the writing OK. FINISHED
CYCLE will appear on the display with a sound
signal.
If the drying has not been selected open the door and
take out the sterilized material.
‰
IGEA
key
key
key
¼
of a handwheel revolution.
checking on the display the exact
Pag. 12 di 45