Overheat Safety Device - Ayce KAARI Manuel D'utilisation

Heating function
The product is equipped with adjustable thermostat by stopping the air flow as soon
as the desired ambient temperature is reached; hot air will start to flow again when
the ambient temperature drops. To select the desired temperature press "+" or "-"
pushbutton after set the power level (minimum, medium or maximum). The set
temperature will display on the display.
The set temperature can be displayed in either °C or °F; to set the unit of
measurement of temperature turn on the product, push and keep pushing "+"
pushbutton until the unit of measurement will flashing on the display. Push "+"
pushbutton to select the desired unit of measurement; wait a few seconds for the
setting to be memorized.
ECO function
To activate ECO function press ECO
This function will compare the target temperature with the current ambient
temperature and it will automatically select the most appropriate heating power
level to guarantee an optimum comfort level while reducing the energy
consumption. (Attention: this function is available only if one power level 1, 2 or 3 is
selected). When the ECO function is on, ECO is displayed and the appliance may
switch automatically to a lower or higher heating level even several time. The
corresponding heating level is always shown on the display.
Timer function
The appliance is equipped with 24 hours timer that allow to set the automatic start
or automatic off of the product. To set the automatic start: when the product is in
stand-by mode press TIMER pushbutton
before the appliance will be turned on blink on the display. To adjust the timer
press "+" or "-" pushbuttons then wait a few seconds for the setting to be memorized.
On display stand-by icon and timer icon blinking indicating that the timer for auto
on is set. When the programmed time is reached, the appliance is turned on with
the setting used during the previous period of operation. Attention: when the timer
for auto start is seted do not turn off the product from the main switch.
To set automatic off: when the product is on, press TIMER pushbutton;
the TIMER icon and the time remaining before the appliance turn off blink on the
display. To adjust the timer press "+" or "-" pushbuttons then wait a few seconds
for the setting to be memorized. On display timer icon blinks indicating that the
timer for auto off is set. When the programmed time is reached, the appliance is
turned off automatically.
To deactivate timer function press TIMER pushbutton twice. When timer is set push
TIMER pushbutton one time to check the remaining time.
Timer steps (value show on the display): 15 M (M=minutes), 30 M, 45 M, 1,0 H (H=hour),
1,5 H, 2 H, 2,5 H, 3 H, 3,5 H, 4 H, 4,5 H...until 10 H; from 10 H to 24 H step 1 hour.
pushbutton. The ECO icon will be displayed.
; TIMER icon and the time remaining
Every time one pushbutton is pushed the appliance emit "beep" sound.
This function can be activated/deactivated: when product is working push
and keep pushing "-" pushbutton until the display will show "b0" or "b1" flashing.
Press "-" pushbutton to select "b0" (beep off) or "b1" (beep on); waiting a few
seconds for the setting to be memorized.
TIP - OFF SAFETY DEVICE
This appliance is provided with a safety device which will switch off the heater in
case of accidental tipping off. To reset, disconnect the plug from the power for a
few minutes, remove the cause of tipping off, then plug the appliance in again. If it
still cannot be reset, return heater to your nearest service center for examination
or repair.

OVERHEAT SAFETY DEVICE

Your heater is fitted with a safety device to switches off the heater in the event of
overheating. If the safety device operated, please turn the heater off, unplug the
appliance and let it completely cool, inspect for blockage of air inlet or outlet,
attempting to restart the heater then after.
If the heater fails to operate or the safety device switches the heater off again,
return heater to your nearest service center for examination or repair.
MAINTENANCE
1. Always disconnect the appliance and let it completely cool before any
maintenance.
2. Use a vacuum cleaner to remove dust on grilles.
3. Clean the outside of the unit with a damp cloth and then dry it with a dry cloth.
Never immerse the unit in water, nor let water drip into the unit.
Clean the filter:
Gently remove the back grill by pulling it outwards,
remove the filter and clean it using a soft slight damp
cloth then replace in the appliance and reseal the back
grill.
50 | 51
GB