Table des Matières
Publicité
TAB: 7539
Adjustments
Chime volume adjustment
The chime volume can be set to 10 levels.
Press the - button to decrease the volume of the tune, the +
button to increase the volume of the tune )see Fig. 11(.
1) Press and hold down the button
starts blinking accompanied by an audible warning.
2) Press the + or - button )on the left side of the indoor station(
to play and adjust the chime volume.
3) Repeatedly press the + or - button to select the volume you
want.
4) Press the button
to save the tune or wait 15s. At the end
of configuration, the button
Brightness adjustment
Adjustment is possible during communications and self-starting,
press the - and + button on the right-hand side to adjust the
brightness.
Contrast adjustment (volume button)
Adjustment is possible during self-starting )without activating the
voice unit). Press the - or + button on the left-hand side to adjust
the contrast
External call voice unit volume adjustment (10 levels
with indoor station in a conversation)
Use the + and - buttons on the left-hand side to adjust the
desired level. It is adjusted during a conversation.
Internal call voice unit volume adjustment (10 levels
with indoor station in a conversation)
Use the + and - buttons on the left-hand side to adjust the
desired level. It is adjusted during a conversation.
Muting
the
chime
To mute the chimes, press the
)approximately 2s(. Deactivation is confirmed with a "low-
pitched" tone and the
button lighting up with a steady light.
Chime reactivation is signalled by a "high-pitched" tone and the
button going out. With the user away, the indoor station is
able to keep up to 4 missed calls in memory by blinking the
button. Saving to memory consists of one flash per missed
call. The signalling takes place with flashes every 10s. When
the chime is restored the counter is reset. This function can be
activated with the indoor station at reset.
)for 2 s( until button
stops blinking.
(User
Away
function)
button and hold it down
Operation
Caution: For the indoor station to work, the ID code must have
already been configured. To check this, press a button
the monitor )but not the buttons and the volume and brightness
buttons): if an ID has been assigned to the monitor, one beep
will sound, if no ID has been assigned or it has been deleted, 3
beeps will sound.
Answering a call
Press the button
. To end the conversation, press the
button
again .
FP/M Landing calls (see "FP/M connection variant"
wiring diagrams)
The duration of the chime cycle depends on how long the button
is pressed, for a maximum time of 10s.
Making an intercommunicating call
To make a call to another indoor unit, one or more buttons must
have been programmed )see "Button configuration" section(.
Press
the
programmed
to call. During the call, the indoor station emits a
tone in order to signal that the call is being made.
If the indoor station is already engaged with another call, a
tone will be heard on the indoor station making the call to
indicate that the user receiving the call is busy. When the
called party answers, the communication is automatically
activated. To end the conversation, press the button
The maximum length of a conversation is 5 minutes.
Temporarily muting the chime
When you receive a call, you can temporarily mute the chime by
pressing the button
.
Lock command
Press the
button to send a lock opening command )by
default, the last entrance panel to make a call).
Self-start
-
Self-start
with
To self-start to the master panel, briefly press the button
. Only incoming video is activated. To activate the voice unit,
press the button
. To end the conversation, press the button
again
. If any communication is already in progress, a busy
tone will be heard at the indoor station making the call.
Calling a concierge switchboard
To make a call to a concierge switchboard )if installed in the
system), press the
the call by pressing the
button flashes.
EN
button
for
the
extension
dedicated
button
button and, with a timeout of 5s, send
button. During the timeout the
on
.
19
Publicité
Table des Matières
