Festool PRECISIO CS 70 EB Notice D'utilisation page 20

chine comes to a standstill.
Maintain your machine regularly to make sure it
functions reliably:
- Use an extractor to remove the dust deposits.
- Keep the guide rods clean and grease regu-
larly.
- Keep the toothed gears behind the rotary han-
dle [2-3] clean.
- Replace worn or damaged table inserts [1-4].
- If wood chips block up the extraction channel
on the lower protective cover, unscrew the ro-
tary knob [5-8] and move the fl ap [5-6] approx.
8 mm to open up a gap so that the blockage is
removed.
- If the blockage is serious or the saw seizes
when the initial cut is made, unscrew the fas-
teners [5-7] using the hexagon wrench so that
the fl ap [5-6] can be opened completely. Close
the fl ap again prior to use.
- After completing work, wind up the power ca-
ble onto the holder [1-3].
- A damper allows the saw unit to retract evenly
along the entire cutting length. If this is not the
case, the damper can be adjusted through the
hole [3-5].
Filter cleaning (CS 70 EB only)
You should clean the air intake fi lter [3-2] if the
temperature monitor (see 7.1) triggers shutdown
cycles more frequently without the machine be-
ing overloaded excessively.
Unscrew the rotary knob [3-1].
Remove the fi lter insert.
Knock off the dust or use an extractor on the
surface of the fi lter.
Insert the fi lter again.

If damaged, replace the fi lter with a new fi l-
ter cartridge.
10 Accessories
Use only original Festool accessories and Fes-
tool consumable material intended for this ma-
chine because these components are designed
specifi cally for the machine. Using accessories
and consumable material from other suppliers
will most likely affect the quality of your work-
ing results and limit any warranty claims. Ma-
chine wear or your own personal workload may
increase depending on the application. Protect
yourself and your machine, and preserve your
warranty claims by always using original Festool
accessories and Festool consumable material!
20
11 Disposal
Do not throw the power tool in your household
waste! Dispose of machines, accessories and
packaging at an environmentally-responsible
recycling centre. Observe the valid national reg-
ulations.
EU only: European Directive 2002/96/EC stipu-
late that used electric power tools must be col-
lected separately and disposed of at an environ-
mentally responsible recycling centre.
12 Warranty
For our tools, we give warranty for material and
production defects in accordance with the lo-
cally applicable legal provisions, but in any case
for at least 12 months. Within the EU member
states, the warranty period is 24 months (verifi -
cation through invoice or delivery note). Damage
caused by, in particular, natural wear, overload-
ing, incorrect handling, or damage caused by the
operator, or damage caused through use of the
equipment contrary that specifi ed in the Oper-
ating Instructions, or damage which was known
at the time of purchase, is not covered by the
warranty. Furthermore, damage caused by the
use of non-original accessories and consumable
materials (e.g. sanding pads) is also excluded.
Complaints can only be recognised if the tool is
returned while still assembled to the supplier or
an authorised Festool Customer Service work-
shop. Keep the Operating Instructions, Safety
Instructions, Spare Parts List and purchase re-
ceipt in a safe place. Otherwise the respective,
current warranty conditions of the manufacturer
shall apply.
Note
Due to continuous research and development
work, we reserve the right to make changes to
the technical content of this documentation.
13 EU Declaration of Conformity
Bench-mounted circular saw
and circular trimming saw
CS 70 E
CS 70 EB
Year of CE mark
We declare under sole responsibility that this
product complies with the following norms or
normative documents:
EN 61029-1, EN 61029-2-1, EN 55014-1, EN
Serial no.
491304, 491305, 493474
491302, 491303, 493559
1995