Accessories - Hoover Chorus CH40PAR 011 Manuel D'utilisation

GETTING TO KNOW YOUR CLEANER
A. Cord Reel Pedal
B. Exhaust Filter Cover
C. Exhaust Filter
D. Parking slot
E. On/Off Pedal
F. Dust Container Assembly
G. Main Body
H. Hose
I. suction Regulator
J. Hose Handle
K. Telescopic Tube
L. Telescopic Tube Adjuster
M. Floor Type selector Pedal*
N. & N1. Carpet and Floor Nozzle (GP)**
N2. Carpet Nozzle (CA)**
N3. Hard Floor Nozzle (HF)**
O. Dust Container
P. Vortex Finder
Q. Pre-motor filter Assembly
R. Dust Container Lid
s. Dust Container Release Button
T. 2 in 1 Accessory
U. Pet Hair Remover Mini Turbo Nozzle*
V. Allergen Remover Mini Turbo Nozzle*
W. Parquet Nozzle*
AssEMBLING YOUR CLEANER
Remove all components from the packaging.
1. Connect the hose to the cleaner main body, ensuring it clips and locks into position.
To release: simply press the button on the hose end and pull. [1]
2. Connect the hose handle to the upper end of the extension tube [2], or accessories
if required.
3. Connect the lower end of the telescopic tube to the Carpet & Floor nozzle** [3] or
accessories if required.
*Certain Models Only ** Certain models only, nozzles may vary according to model
UsING YOUR CLEANER
1. Extract the power cord and plug it into the power supply. Do not pull the cord beyond
the red marker. [4]
2. Adjust the telescopic tube to the desired height by moving the telescopic release button
up and raise or lower the handle to the most comfortable cleaning position. [5]
3. Carpet & Floor Nozzle**. Press the floor type selector on the nozzle [6] to select the
ideal cleaning mode for the floor type.
Hard Floor – Brushes are lowered to protect the floor.
Carpet – Brushes are raised for deeper cleaning.
Carpet & Floor Nozzle**: [7]
- Hard floor Cleaning: Press the pedal on the nozzle on Hard Floor mode and adjust
the slider on the nozzle on ALL FLOORs. In this position brushes, wheels and wiper
blade are lowered to protect hard floors. [7a]
- Standard Carpet & Rugs Cleaning: Press the pedal on the nozzle on Carpet
mode and adjust the slider on the nozzle on ALL FLOORs. In this position brushes and
wiper blade are raised while wheels are lowered to allow a perfect ease of movement on
such surfaces. [7b]
- Deep Carpet Cleaning: Press the pedal on the nozzle on Carpet mode and adjust
the slider on the nozzle on DEEP CARPET CLEANING. In this position brushes, wheels and
wiper blade are raised for a deeper cleaning of your carpet. [7c]
WARNING: It is recommended to avoid potential scratching of wooden floors that
the pedal is not set on hard floor mode and the slider on deep carpet cleaning.
4. switch the cleaner on by pressing the on/off Pedal on the cleaner main body. [8]
5. Adjust the suction regulator on the handle to the desired level. [9]
6. switch off at the end of use by pressing the on/off Pedal. Unplug and press the cord
reel pedal to wind the power cord back into the cleaner. [10]
PARKING AND STORAGE SECTION
The tube and the nozzle can be parked on the back of the cleaner for storage or temporary
storage while in use. [11]

ACCEssORIEs

To obtain the best performance and energy efficiency
correct nozzles are used for the main cleaning operations. These nozzles are indicated
in the diagrams by the letters GP, HF or CA.
A nozzle type GP can be used to clean both carpet and hard floor.
A nozzle type HF is suitable for use only on hard floor.
A nozzle of type CA is suitable for use only on carpet.
2
GB
it is recommended that the
#1