Publicité
14 | English
Secure the workpiece. A workpiece clamped with
u
clamping devices or in a vice is held more secure than by
hand.
This power tool is not suitable for bench-mounted use.
u
It must not be clamped into a vice or fastened to a work-
bench, for example.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Technical Data
Straight Grinder
Article number
Rated power input
W
Power output
W
−1
Rated speed
min
−1
Speed adjustment
min
range
Max. collet diameter
mm
Spanner flat on the
– Clamping nut
mm
– Grinding spindle
mm
Spindle collar dia-
mm
meter
Grinding tool dia-
mm
meter, max.
Polishing tool dia-
mm
meter, max.
Constant electronic
control
Speed preselection
1 609 92A 6N7 | (06.08.2021)
GGS 8 CE
GGS 28 C
3 601 B22 1.. 3 601 B20 0.. 3 601 B20 1.. 3 601 B21 0.. 3 601 B21 1.. 3 601 B25 0..
750
600
420
350
8000
30,000
2500−8000
−
8
8
19
19
19
19
43
43
50
50
80
−
●
●
●
−
Intended Use
The power tool is intended for grinding and deburring metal
with corundum grinding tools, as well as for working with
sanding belt tools.
GGS 8 CE: The power tool is additionally intended for brush-
ing and polishing metal.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1)
Collet
(2)
Clamping nut
(3)
Grinding spindle
(4)
Spindle collar (insulated gripping surface)
(5)
On/off switch (GGS 8 CE/GGS 28 C/GGS 28 CE/
GGS 28 LC/GGS 28 LCE)
(6)
Speed preselection thumbwheel (GGS 8 CE/
GGS 28 CE/GGS 28 LCE)
(7)
Handle (insulated gripping surface)
(8)
Open-ended spanner on the grinding spindle
(9)
Open-ended spanner on the clamping nut
(10)
Inner shank dimension L
(11)
On/off switch (GGS 28 LP)
(12)
Lock-off function for on/off switch (GGS 28 LP)
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
GGS 28 CE
GGS 28 LC
GGS 28 LCE
650
650
380
380
30,000
30,000
10,000–
−
30,000
8
8
19
19
13
13
43
43
50
50
−
−
●
●
●
−
a)
a)
0
GGS 28 LP
650
500
380
280
30,000
30,000
10,000–
−
30,000
8
8
19
19
13
13
43
43
50
40
−
−
●
−
●
−
Bosch Power Tools
Publicité
