Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Deactivating the access code (reset code)
The code can only be reset if the sensor is already in configuration mode.
G
Establish the connection
(chap. 5.2.3)
Activating the configuration mode via the access code
The configuration mode can only be activated with the remote control, if a code was previously stored and the "access code" function is activated.
G
Establish the connection
(chap. 5.2.3)
Deactivating the access code without the remote control
Press both [<] and [>] keys simultaneously for 8 s. Caution: All parameters are reset to the default settings!
5.2.6
Setting / changing parameters
In order to prevent the door from opening and closing unnecessarily while the parameters are being set or changed, it can be held open or closed again with the
A
1
ca. 15 min.
Keep the door open manually for
15 min. when making the settings.
Afterwards the door will close when
there is no object within the detection
area.
Enhanced functions
Recommendation: First, select the enhanced function that is closest to the requirements and then change the parameter levels correspondingly.
Parameter
Direction recognition
Field size
Relay hold interval
SMD function
Mounting height
Cross traffic
Interference suppression
SMD field size
Field geometry
10
+
C
9
Press
+
C
9
→
+
light up, i.e. the "access
C
1
code" function is activated
(the code has been stored)
+
C
9
Press
+
C
9
→
+
light up, i.e. the "access
C
1
code" function is activated
+
(→ If
light up, the "access
C
2
code" function is deactivated)
A
2
Door closes when no object is in the
detection area; afterwards standard
operation.
+
*
C
1
Key code
Standard
C
1
B
ON, forwards
D
6
+
F
1
1 s
+
F
3
Off
+
F
4
Up to 3 m
+
F
5
Low
+
Off
F
6
+
F
7
1
+
Wide
F
8
Montageanleitung GC 302 SV
4 x 9
4x
Press
four times
9
Code
Enter a 4-digit code.
A
3
Configuration mode is ended; door clo-
ses when no object is in the
detection area; afterwards standard
operation.
+
+
C
2
C
3
Pavement
Retirement home
C
2
C
3
ON, forwards
OFF
7
6
0.8 s
2 s
Off
Decreasing, 2 s
Up to 3 m
Up to 3 m
Medium
Off
Off
Off
1
5
Narrow
Wide
C
Confirm by pressing
→
+
light up, i.e. the "access
C
2
code" function is deactivated
(the code is reset)
C
4x
Confirm by pressing
→
light up, i.e. the configura-
+
C
1
tion mode is activated and the
sensor is ready for programming
(→ If
+
light up, the code was
C
2
incorrect; restart at 1)
+
+
C
4
C
5
Entry hall
Supermarket
C
5
C
4
ON, forwards
ON, forwards
6
9
0.2 s
1.5 s
Off
Decreasing, 2 s
Up to 3 m
3-4 m
Low
Off
Off
Off
1
5
Narrow
Wide
123456, 70705-9-9520 Ä-St.1
C
C
A
function.
+
C
6
High mounting
C
6
>
3 m
(9.84')
ON, forwards
9
1 s
Off
3-4 m
Medium
Off
1
Wide
* Factory setting
Publicité
Table des Matières
