Chicco Oasys 2.3 Mode D'emploi page 20

Parts
A. Headrest
B. Diagonal belt guide
C. Backrest
D. Armrests
E. Seat
F. Lap belt guide
G. Cup holder
H. Reclining adjuster button
I. Safety belt guide open/close button
J. Cup holder clip
K. Backrest width adjuster wheel
L. Backrest height adjuster lever
M. Rear pocket for instruction booklet
N. Side wings
O. Rigid FixPlus clasp lever
P. Rigid clasps
Q. Indicators
R. Rigid clasp release system buttons
Fitting the child car seat inside the vehicle us-
ing safety belts and placing the child inside
WARNING! These instructions and diagrams are
for the installation of the child car seat on the
right back seat.
To fi t the child car seat in other positions, carry
out these operations in the same order.
1. Place the child car seat onto the vehicle seat
with the backrest up against the vehicle seat
backrest
WARNING! Check that the vehicle headrest does
not interfere with the child seat headrest: it must
not push it forwards (Diag. 6). If this happens,
remove the headrest from the vehicle seat where
you intend to install the child car seat. Remember
to replace the vehicle headrest when the child car
seat is removed and a passenger uses the seat.
WARNING! The rear side of the child car seat
must be resting against the vehicle seat.
2. Place your child inside the car seat with his back
correctly placed against the backrest.
3. Check the backrest height (see paragraph "AD-
JUSTING THE HEIGHT OF THE BACKREST")
4. Check the backrest width (see paragraph "AD-
JUSTING THE WIDTH OF THE BACKREST")
5. Thread the diagonal car seat belt through the
diagonal belt guide (B). Check that the belt
guide (l) open/close button is fi rmly closed; you
must be able to see the white reference line
(Diag. 7).
6. Connect the car safety belt by threading the
lap belt trough the red lap belt guides (F) under
the two armrests in line, and by threading the
diagonal belt under the armrest on the side of
the fastener buckle (Diag. 8).
7. Pull the diagonal car safety belt upwards, to
ensure the belt is taut and fi tting properly over
the child's legs and chest; don't tighten it too
much!. (Diag. 9)
WARNING! Check that the car safety belt is tight
enough.
WARNING! Check that the car safety belt is not
twisted (Diag. 10).
WARNING! Check that the diagonal safety belt
fi ts correctly across the child's shoulder (Diag.
9) and does not press on the neck; adjust the
backrest accordingly (see paragraph "ADJUST-
ING THE HEIGHT OF THE BACKREST").
WARNING! Check that the car safety belt adjust-
er is behind the backrest of the car seat (or at least
aligned to it) (Diag. 5).
WARNING! Do not fi t the car safety belt in any
way other than that indicated in these instruc-
tions! (Diag. 11)
WARNING! Check that the child is strapped into
the child car seat correctly so that he cannot slide
forwards.
Check that any unused rigid clasps are hidden
away in the compartment at the back.
Fitting the child car seat inside the vehicle
using safety belts and rigid FixPlus clasps and
placing the child inside
WARNING! Before installing the child car seat us-
ing the FixPlus clasps, check the child car seat is in
a vertical and not reclined position.
WARNING! These instructions and diagrams are
for the installation of the child car seat on the
right back seat. To fi t the child car seat in other
positions, carry out these operations in the same
order.
IMPORTANT! The child car seat MUST ALWAYS be
installed using the car safety belts. The rigid Fix-
Plus clasps are an additional device to the use of
car safety belts and aim to provide greater stabil-
ity for the child car seat.
1. Place the child car seat onto the vehicle seat
with the backrest up against the vehicle seat
backrest (diag. 12)
WARNING! Check that the vehicle headrest does
not interfere with the child seat headrest: it must
not push it forwards (Diag. 6). If this happens, re-
move the car seat headrest. Remember to replace
the vehicle headrest when the child car seat is re-
moved and a passenger uses the seat.
2. Pull the lever (O), located under the inclination
adjuster button (H), upwards. (Diag. 13)
3. While keeping the lever pulled, pull out the rigid
clasps (P) completely from the rear of the back-
rest (diag. 14).
4. Insert the two rigid clasps (P) into the corre-
20