IKAR HWB 1,8 Mode D'emploi page 14

16. The IKAR fall arrester can be used in conformity with EN 360:2002, CSA Z259.2.2-98, ANSI/ASSE Z359.1-
2007, Z359.14-2014 within a temperature range between -40°C (-22°F) and +50°C (+122°F) (
17. The max. working load of the person to be secured is 136 kg. (
18. Fall arresters have to protected against the impact of welding fl ames and sparks, fi re, acidic substances,
alkaline substances and alike.
19. Do not apply any modifi cations or repairs to the fall arrester (
Repairs may only be carried out by the manufacturer or persons trained and authorised by the manufacturer.
20. Fall arresters may only be used by persons who have been trained accordingly or have been instructed by a
competent person. The person using the device shall not have any physical or health impairments. (Alcohol,
drug or medication abuse, cardiovascular problems)
21. The service life of the fall arrester has to be determined during each annual inspection; depending on wear, it
is approx. 10 years.
22. The fall arresters of types HWB / HWPB / HWS / HWPS which are equipped with a hook clamp swivel
mounting should be attached to the anchor points in such a way that no transverse or bending load can
impact the hook clamp swivel mounting. This is of particular importance in case of a fall.
23. The fall arresting devices (HWB 2 and HWPS 3-type) can also be equipped with a special swivel (SW-type).
24. The suitability for use of a fall arrester with horizontal fall protection in conformity with the current standards
should be verifi ed by suitable tests on the complete system.
1. The cable / webbing should be rolled up only with a load applied. Never pull the cable / webbing out entirely
and the release it as the sudden impact of the snap hook on the device may cause the return spring to break
( ).
11
2. For devices which are continually exposed to outdoor conditions it is recommended to grease the steel cable
with acid-free oil or Vaseline in regular intervals (for steel cables only).
3. The retractable lanyard is made of PES / Dyneema and must be cleaned with warm water or neutral cleaning
agents only. Do not use thinner or the like. Use clean water to rinse away any cleaning agent residue.
Attention: Please note! The fall arresters have to stored and transported in a dry, dust-free and oil-free
4.
environment.
5. Textile components which have become wet due to cleaning or use have to be dried by natural means only.
Do not dry near fi re or similar sources of heat.
6. Before using disinfectants, you have to contact the manufacturer due to the complex legal product
classifi cations based on the specifi c applications and constituents.
Please note: The fall arresting device has been successfully tested for horizontal application and a fall
over the edge simulated from this. Here an edge radius r = 0.13 mm was used for fall arresting devices
with fastener made from webbing ( 12 ). Based on this test, the fall arresting device is suitable for use over
similar edges with a radius of r ≥ 0.5 mm (12a) according to EN and r ≥ 0.13 mm in the USA, as are typically
present on rolled steel profi les,
on wooden beams or on a panelled, rounded fascias. . In addition, wall arresters with wire cable are also
suitable to withstand wear by edges such as that of fl exible (non-reinforced) trapezoidal sheet metal, pre-
cast concrete elements or poured-in-place concrete edges. Notwithstanding this test, the following must
be observed at all times or horizontal or inclined use in which the risk of a fall over an edge exists:
1. A risk assessment has to carried out prior to starting work. If the edge over which a fall may occur is a
particularly "cutting" edge and / or is not free of burrs (e.g. uncovered parapet or sharp, reinforced sheet
metal edge) appropriate precautions shall be taken prior to starting work.
- a fall over the edge has to be excluded
and
- the max. working load of the devices for the stress sustained during a fall over edges (
and
- an edge protector has to be installed prior to starting work
In cases of doubt it is recommended to contact the manufacturer.
2. The anchor point of the fall arrester shall not be below the surface (e.g. platform, fl at roof) the person using
the device is standing on (
ENGLISH
Care and maintenance
Horizontal use
).
13
).
9
).
10
14
8
).
8
40
9
10
11
12
12a
) must not be
9
40