Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
• Use only connecting attachments with a rubber plug device
for severe requirements
water.
• Check connecting attachments for defects or ageing before using
them.
• Never use defective connecting attachments.
• When laying the connecting attachments, be sure that they do
get crushed or bent, and that the plug-and-socket connection does
not get wet.
• Do not use any temporary electrical connections.
• Never bridge over protective devices or put them out of operation.
• Only connect with residual current circuit breaker (30 mA).
A licensed professional electrician must make all electrical
connections and repairs, and observe local regulations in doing so,
especially those regarding protective measures.
The manufacturer or a company designated by the manufacturer
must attend to the repair of all electrical parts on the machine.
S
t
a
r
t
-
u
p
S
t
a
r
t
-
u
p
Observe all safety instructions.
Setting up the machine:
• Set up the machine on a solid, level base.
• Keep the machine from sinking into the ground or floor.
Adhere to accident prevention regulations (danger of tipping).
• When setting up the machine, make sure that the mixing drum
can be emptied without obstruction.
Switching on and off
Be sure that
-
all protective devices are on the mixer and properly mounted.
-
all safety instructions are adhered to.
• Switch the motor on and off only at the switch.
• In the event of a power failure, the machine will switch off
automatically. Press the switch again to restart the machine.
Motor protection
The motor is equipped with a thermostat. The thermostat switches the
motor off automatically in the event of overload (overheating). The
machine can be restarted after a cooling-off period.
M
i
x
i
n
g
M
i
x
i
n
g
• Only use mixer for applications listed under "Correct use".
• Check the stability of the mixer.
• Only fill or empty the mixing drum while the motor is running.
• Observe the nominal filling volume!
• An electrical safety shutdown prevents the mixer operating while
the safety grid is open. Check functionality of safety shutdown
before commissioning.
Mixture production:
1. Close safety grid.
2. Switch on mixer.
that is protected against spraying
3. Fill with water and aggregate (sand, ...).
4. Add binding agent (cement, lime, ...).
5. Repeat points 3 and 4 until required mixture ratio has been
achieved.
6. Blend mixture well.
Have a professional advise you regarding the composition and
quality of the material being mixed.
Prepared (commercially available) mixture production:
Observe mixing ratio and details given by manufacturer on packaging.
1. Close safety grid.
2. Switch on mixer.
3. Fill with required volume of water.
4. There is a sack opener on the safety grid which is used to tear
open the packed mixture and filling the drum.
5. Blend mixture well.
Emptying the mixing drum:
The drum is emptied through an opening in the base which is opened
by actuating a lever.
See page 29 for instructions on emptying.
T
r
a
n
s
p
o
r
t
T
r
a
n
s
p
o
r
t
Pull plug each time before transport.
For loading see page 30.
S
t
o
r
a
g
e
S
t
o
r
a
g
e
The mixer should be cleaned thoroughly before long storage periods
and moving parts treated with an environmentally-friendly spray oil.
This lengthens the useful life of a mixer and ensures smooth operation
of the device.
C
l
e
a
n
i
n
g
C
l
e
a
n
i
n
g
Additional safety instructions
Pull plug each time before cleaning.
• Switch off machine and pull plug if you have to touch the machine
(with hand, brush, scraper, rag, etc.) while cleaning it.
• Protective devices removed for cleaning must be properly
remounted before starting the machine.
• Do not spray the motor and switch directly with a water jet.
• Remove agitator head to clean (
Notes on cleaning:
• Before taking a break and after finishing work, clean the mixer
inside and out.
• Do not beat on the mixing drum with hard objects (hammer,
shovel, etc.). A dented mixing drum impairs mixing operations and
is difficult to clean, besides.
see page 30).
6
Publicité
Chapitres
Table des Matières
