Bosch GKT 55 GCE Professional Notice Originale page 16

OBJ_BUCH-1471-001.book Page 16 Wednesday, July 13, 2011 10:56 AM
16 | English
32 Cutting mark, 0°
33 Cutting mark, 45°
34 Plastic insert for base plate
35 Knurled screws for play adjustment of guide groove
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Circular Saw
Article number
Rated power input
No-load speed
Rotational speed under load, max.
Cutting depth, max.
– for 0° bevel angle
– for 45° bevel angle
Spindle lock
Speed preselection
Constant electronic control
Reduced starting current
Base plate dimensions
Saw blade diameter, max.
Saw blade diameter, min.
Blade thickness, max.
Tooth thickness/setting, max.
Tooth thickness/setting, min.
Mounting bore
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.
Please observe the article number on the type plate of your machine.
The trade names of the individual machines may vary.
Noise/Vibration Information
Measured sound values determined according to EN 60745.
Typically the A-weighted noise levels of the product are:
Sound pressure level 92 dB(A); Sound power level
103 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745:
2
Cutting wood: a <2.5 m/s , K=1.5 m/s
h
2
Cutting metal: a <2.5 m/s , K=1.5 m/s
h
The vibration emission level given in this information sheet
has been measured in accordance with a standardised test
given in EN 60745 and may be used to compare one tool with
another. It may be used for a preliminary assessment of expo-
sure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
1 609 929 Y20 | (13.7.11)
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working pe-
riod.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
GKT 55 GCE
accessories, keep the hands warm, organisation of work pat-
Professional
terns.
3 601 F75 0..
Declaration of Conformity
W 1400
We declare under our sole responsibility that the product de-
-1
min 3600 – 6250
scribed under "Technical Data" is in conformity with the fol-
-1
min 5900
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2004/108/EC,
mm 57
2006/42/EC.
mm 42
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider
Senior Vice President
Engineering
mm 154 x 305
mm 165
mm 160
mm 1.8
Robert Bosch GmbH, Power Tools Division
mm 2.6
D-70745 Leinfelden-Echterdingen
25.05.2011
mm 1.8
mm 20
Assembly
kg 4.7
Mounting/Replacing the Saw Blade
/ II
Before any work on the machine itself, pull the mains
plug.
When mounting the saw blade, wear protective gloves.
Danger of injury when touching the saw blade.
Only use saw blades that correspond with the charac-
teristic data given in the operating instructions.
Do not under any circumstances use grinding discs as
the cutting tool.
Selecting a Saw Blade
An overview of recommended saw blades can be found at the
end of this manual.
Removal of the Saw Blade (see figure A)
2
,
Adjust the maximal cutting depth, see section "Adjusting the
2
.
Cutting Depth".
For changing the cutting tool, it is best to place the machine
on the face side of the motor housing.
– Pivot lever 3 toward the front.
– Push lock-off button 2 toward the front and press the saw
toward base plate 7 until it engages in the position for
changing the saw blade.
– Press the spindle lock button 25 and keep it pressed.
Dr. Eckerhard Strötgen
Head of Product
Certification
Bosch Power Tools