Automatic Input Switching (Auto Function) - Pioneer PDA-5003 Mode D'emploi

Other Operations
Automatic input switching
(AUTO FUNCTION)
The Plasma Display is equipped with an [AUTO FUNCTION]
detection function; when a signal is detected at the
selected input, the function selector automatically
switches to that input.
Remote control unit
DISPLAY
STANDBY/ON MENU
/ SET
MENU SET
Display operating panel
1
Press the MENU button to display the menu
screen.
M E N U
P I C T U R E S C R E E N
C O N T R A S T
B R I G H T N E S S
C O L O R
T I N T
S H A R P N E S S
P I C T U R E R E S E T
SET ENTER
40
En
MENU
2/3
SET
5/∞
INPUT SCREEN SIZE – VOL +
5/∞ 2/3
I N P U T 1
S E T U P O P T I O N
0
:
0
:
0
:
: 0
0
:
MENU EXIT
2 Use the 2/3 buttons to select [OPTION].
M E N U
P I C T U R E S C R E E N
L A N G U A G E
E N E R G Y S AV E
T I M E R S E T T I N G
S C R E E N M G T.
A U T O S E T U P M O D E
A U T O F U N C T I O N
P I P D E T E C T
S P L I T F R E E Z E
SET ENTER
3 Use the 5/∞ buttons to select [AUTO FUNCTION].
M E N U
P I C T U R E S C R E E N
L A N G U A G E
E N E R G Y S AV E
T I M E R S E T T I N G
S C R E E N M G T.
A U T O S E T U P M O D E
A U T O F U N C T I O N
P I P D E T E C T
S P L I T F R E E Z E
SET CHANGE
4
Press the SET button to select the desired [AUTO
FUNCTION] setting.
The factory default setting is [OFF]. Each time the
SET button is pressed, the selector function switches
alternately as shown:
3 OFF
INPUT4 2
÷OFF ..... [AUTO FUNCTION] is disabled.
÷INPUT1 or INPUT4...
÷ If a signal is detected to the selected input
jack, the input function will automatically
switch to the selected input.
÷ After the [AUTO FUNCTION] mode has
caused the input to switch, if the input
signal is no longer detected, the input
source reverts to the one selected before
operation of the [AUTO FUNCTION] mode.
÷ If the input changes when the unit is in
[AUTO FUNCTION] mode, pressing the
INPUT button to select a different input will
cause the [AUTO FUNCTION] mode to be
temporarily disabled, but it can be enabled
again by turning the power ON/OFF.
5
When finished with the setting, press the MENU
button to return to the normal screen image.
Notes
÷ The [AUTO FUNCTION] for [INPUT1] is supported only when a
separate SYNC or composite SYNC analog RGB signal is input.
(When a G ON SYNC or component video signal is input,
[AUTO FUNCTION] is disabled.)
÷ The [AUTO FUNCTION] setting affects all input sources.
I N P U T 1
S E T U P O P T I O N
: E N G L I S H
: S TA N D A R D
: I N A C T I V E
: O F F
: A C T I V E
: O F F
MENU EXIT
I N P U T 1
S E T U P O P T I O N
: E N G L I S H
: S TA N D A R D
: I N A C T I V E
: O F F
: A C T I V E
: O F F
MENU EXIT
INPUT1 2