Onkyo CR-N775D Mode D'emploi page 45

> Before Start > Part Names
to the latest version.
If an error message is displayed: When an error
occurs, "¢-¢¢ Error!" is displayed on the display of
this unit. ("¢" represents an alphanumeric character.)
Check the following:
0 ¢-01, ¢-10: Ethernet cable not found. Connect the
Ethernet cable properly.
0 ¢-02, ¢-03, ¢-04, ¢-05, ¢-06, ¢-11, ¢-13, ¢-14,
¢-16, ¢-17, ¢-18, ¢-20, ¢-21: Internet connection
error. Check the following:
– The router is turned on
– This unit and the router are connected via the
network
Try to disconnect and then connect again the power
to the unit and router. This may solve the problem. If
you are still unable to connect to the Internet, the
DNS server or proxy server may be temporarily
down. Check the service status with your ISP
provider.
0 Others: Disconnect then reconnect the power cord,
then repeat from the beginning.
Updating via USB
0 Prepare a 128 MB or larger USB storage device
(FAT16 or FAT32 file system format).
0 Delete any data stored on the USB storage device.
0 Turn off the controller component (PC etc.)
connected to the network.
0 Stop any playing Internet radio, USB storage device,
or server content.
0 Some USB storage devices may take long to load,
may not be loaded correctly, or may not be correctly
fed depending on the device or their content.
0 We will not be liable whatsoever for any loss or
damage of data, or storage failure arising from the
> Install > Initial Setup
use of the USB storage device with this unit. Thank
you for your understanding.
1. Connect the USB storage device to your PC.
2. Download the firmware file from our company's
website to your PC and unzip.
Firmware files are named in the following way:
ONKCRN¢¢¢¢_¢¢¢¢¢¢¢¢¢¢¢¢¢¢_¢
¢¢.zip
Unzip the file on your PC. The number of unzipped
files and folders varies depending on the model.
3. Copy all unzipped files and folders to the root folder
of the USB storage device.
0 Make sure to copy the unzipped files.
4. Connect the USB storage device to the USB port of
this unit.
0 If you connect a USB hard disk drive to the USB
port of the unit, we recommend that you use its
AC adapter to power it.
0 If the USB storage device has been partitioned,
each section will be treated as an independent
device.
5. The menu is displayed on the display when
button on the remote controller is pressed.
Menu
Network
Option
Timer
System Information
6. Press 3/4 and ENTER to select "Update" - "via
USB" in order.
> Playback
Supplementary information |
0 You will not be able to select "Update" if there is
no firmware update.
7. Press ENTER to start the firmware update.
0 "Update Complete" is displayed when the update
is complete.
8. Press Í ON/STANDBY on the main unit to switch
the power of the unit off. If you do nothing, then the
power will turn off automatically after 3 minutes. The
process is completed and your firmware is updated
to the latest version.
9. Remove the USB storage device from this unit.
If an error message is displayed: When an error
occurs, "¢-¢¢ Error!" is displayed on the display of
this unit. Check the following:
0 ¢-01, ¢-10: USB storage device not found. Check
whether the USB storage device or USB cable is
Asb
correctly inserted to the USB port of this unit.
Connect the USB storage device to an external
power source if it has its own power supply.
0 ¢-05, ¢-13, ¢-20, ¢-21: The firmware file is not
present in the root folder of the USB storage device,
or the firmware file is for another model. Retry from
the download of the firmware file.
0 Others: Disconnect then reconnect the power cord,
then repeat from the beginning.
Advanced Setup
Asb
Update
via Network
via USB
En
| Others
45