Front Drive Unit (4Wd Model); Regulating The Grass Catcher Retaining Pawl Spring; Storage; Handling And Transportation - Stiga T 102 Série Manuel D'utilisation

Masquer les pouces Voir aussi pour T 102 Série:
Table des Matières

Publicité

8.8 FRONTDRIVEUNIT(4WDMODEL)
This is a sealed single unit that does not
require maintenance. It is necessary to check 
the oil in the hydraulic coupling circuit, top 
it up and change it at regular intervals.
Check that the oil level in the hydraulic 
system is between the «MIN» and 
«MAX» markers on the tank.
If the level is below the «MIN» 
reference marker (Fig. 56):
– remove the guard (fig. 56.A), which 
is secured by the nut (fig. 56.B):
– unscrew the plug (fig. 56.C) and top 
up using 10W30 oil until the level
reaches the «MAX» marker:
– replace the plug (fig. 56.C) 
and the guard (fig. 56.A).
IMPORTANT If it becomes necessary to
top-up the oil level frequently, check the oil
tubes and tank for leaks and contact your
Dealer for the necessary maintenance.
8.9 REGULATING THE GRASS
CATCHER RETAINING
PAWL SPRING
If the grass catcher bag tends to jolt or
open unexpectedly while driving over 
uneven ground, or if it is difficult to 
recouple the retaining pawl after emptying 
the bag, it may be necessary to adjust 
the tension on the spring (fig. 57.A).
Adjust the mounting point by selecting the 
hole (fig. 57.B) that provides the desired result.

9. STORAGE

When you intend to put your machine 
away for more than 30 days:
1. Wait for the engine to cool
2. Disconnect the battery cables and 
store it in a cool and dry place.
3. Empty the fuel tank (par. 7.2.2) and follow 
all the instructions in the engine manual.
4. Clean the machine thoroughly.
5. Check the machine for any 
damage. If necessary, contact the 
Authorised Service Centre.
6. Store the machine:
– with the cutting device assembly lowered
– in a dry place
– protected from inclement weather
– covered with a sheet where 
possible (par. 15.4)
– in a place where children cannot get to it
– making sure that keys or tools used 
for maintenance are removed.
Before starting to use the machine again:
• check that there are no fuel leaks from 
the tubes, fuel stopcock or carburettor:
• prepare the machine as described in 
chapter "6. Using the machine" .

10. HANDLING AND TRANSPORTATION

• When handling the machine, always:
– disengage the cutting device;
– bring the cutting device assembly 
to the highest position;
– stop the engine;
• When transporting the machine 
on a vehicle or trailer, always:
– use an access ramp of suitable 
strength, width and length;
– load the machine with the engine 
switched off, with the key removed from 
the ignition, without a driver and pushed 
by an adequate number of people;
– close the fuel tap (if provided);
– lower the cutting -device assembly;
– engage the parking brake;
– position it so that it does not
cause a hazard to anyone;
– fasten firmly to the device of transport using 
ropes or chains to prevent it from tipping 
over causing damage and fuel leaks.

11. ASSISTANCE AND REPAIRS

This manual provides all the necessary 
information to run the machine and for correct 
basic maintenance operations which can 
be performed by the user. Any regulations 
and maintenance operations not described 
herein must be carried out by your Dealer 
or Authorised Service Centre, which have 
the necessary knowledge and equipment to 
ensure that the work is carried out correctly, 
maintaining the correct degree of safety and the 
original operating conditions of the machine.
Any operations performed in unauthorised 
centres or by unqualified persons will totally 
invalidate the Warranty and all obligations 
and responsibilities of the Manufacturer.
• Only Authorised Service Centres can carry 
out guaranteed repairs and maintenance. 
EN - 26

Publicité

Table des Matières
loading

Table des Matières