Assembly; Assembly Components; Steering Wheel Assembly - Stiga T 102 Série Manuel D'utilisation

Masquer les pouces Voir aussi pour T 102 Série:
Table des Matières

Publicité

distance from the machine (for models 
with side discharge function only).
F.
Grass catcher: in addition to collecting
the mown grass, the grass catcher also 
constitutes a safety element, since it 
prevents any objects picked up by the 
cutting device from being projected 
long distance from the machine (for
models with rear collector only).
G. Discharge chute: this is the part
connecting the cutting device
assembly to the grass catcher (for
models with rear collector only).
H. Driving seat: this is where the 
machine operator sits. It has a sensor 
connected to safety devices for detecting 
the presence of the operator.
I.
Steering wheel: turns the front wheels.
J.
Front bumper: this protects the
front section of the machine.
K. Battery: provides the energy for starting the 
engine. Its specifications and regulations 
for use are described in a specific manual.

4. ASSEMBLY

The safety regulations to follow
are described in chap. 2. Strictly
comply with these instructions to
avoid serious risks or hazards.
For storage and transport purposes, some 
components of the machine are not installed 
in the factory and have to be assembled after 
unpacking. Follow the instructions below.
Unpacking and completing the assembly
should be done on a flat and stable surface,
with enough space for machine handling
and its packaging, always making use of
suitable equipment. Do not use the machine
until all the indications provided in the
"ASSEMBLY" section have been carried out.

4.1 ASSEMBLY COMPONENTS

The packaging holds the components needed 
for assembly as listed in the table below:
Description
1
Steering wheel
2
Dashboard cover and steering
wheel assembly parts
3
Driving seat
4
Front bumper (if fitted)
5
Bag with mounting screws etc. and in-
structions TS-TX-TH models only) (mod-
els with rear collector only)
6
Grass catcher bag supports and asso-
ciated attachments (models with rear
collector only)
7
Side discharge chute (for models with
side discharge only)
8
Cutting device assembly side strength-
eners (if fitted).
9
Envelope containing:
- the instruction manuals and documents 
- driving seat assembly screws
- side discharge chute assembly fittings
(for models with side discharge only)
- the connection screws for the battery 
cables
- 2 starter keys
- 1 spare 10 A fuse
10
Mulching kit (models with side discharge
function only) (if fitted).
4.1.1 Unpacking
1. Carefully open the packaging, paying 
attention not to lose components.
2. Consult the documentation in the 
box, including these instructions.
3. Remove all the unassembled 
parts from the box.
4. Remove the machine from the packaging 
taking the following precautions:
– move the cutting device assembly 
to its maximum height (par. 5.11) to 
protect it against damage when the 
machine is lifted off the base pallet;
– Lift the machine off the base pallet. 
5. Move the front drive release lever to
the released position (par. 5.4).

4.2 STEERING WHEEL ASSEMBLY

1. Put the machine on a flat surface 
and straighten the front wheels.
2. Using a screwdriver, remove the central cap 
(fig. 3.B) from the steering wheel (fig. 3.A).
3. Fit the steering wheel (fig. 3.A) onto the
protruding shaft (fig. 3.C), rotate it so that the
spokes are facing the seat and then push 
it so that the steering wheel hub couples 
with the protruding end of the pin (fig. 3.D).
4. Secure the steering wheel using the screw 
(fig. 3.E) and the washers (fig. 3.F) e (fig. 
3.G) supplied, in the indicated sequence.
5. Tighten the screw (fig. 3.E) fully 
using a socket wrench.
EN - 7

Publicité

Table des Matières
loading

Table des Matières