Getting Started - abc CombBind C110 Manuel D'utilisation

0
Please read these instructions carefully and keep them in a safe place for later reference.
A. GETTING STARTED:
1. Plug the power cord into an appropriate power
receptacle
B. DETERMINE SHEET WIDTH: (see figure 1)
1. Rotate the edge guide to the paper / cover size
you wish to bind. Letter (8-1/2" x 11") A-4
(297mm x 210mm) Oversized (8-3/4" 222mm
x 11-1/4" 286mm) (See figure 1). When using
oversized covers, rotate the edge guide to the
covers position, punch all of the covers for your
documents and set aside. Rotate the edge guide
to either Letter or A-4 position and punch the
paper for your document.
C. PUNCHING PAPER: (see figure 2)
1. To turn the machine "ON" press the on / off
switch located in the rear of the machine. A
green light will illuminate to indicate that the
power is on.
2. Jog or align the sheets or covers and insert the
edge to be punched into the punch throat opening.
3. Fully insert the sheets into the throat opening
and against the edge guide.
4. To punch, press the punch button
The CombBind C-110e will punch up to 15 sheets
of 20 lb. / 80 gsm paper. Do not punch more than
(1) clear cover at a time to prevent jams.
5. If the punch jams the red jam light
illuminate to indicate that the machine has
jammed. The machine will automatically reverse
the punches to clear the jam and the red jam
light will remain illuminated. Remove the paper
and push the punch button to re-set the machine.
The red jam light will turn off indicating that the
machine is ready to punch. Reduce some of the
sheets and repeat steps 2 to 4 to avoid jams on
additional lifts.
6. When finished punching turn the machine OFF
by pressing the ON / OFF switch located at the
rear of the machine.
D. DETERMINE PLASTIC COMB SIZE: (see figure 3)
1. Rotate the binding handle towards you to open
the hooks away from the comb support.
2. Place the document including the covers straight
Specifications C110e
Max. width of paper:
Punching capacity, paper:
Binding capacity:
Net weight:
Dimensions (H x W x D):
Subject to technical changes without prior notice.
up against the comb support to the right side
aligning with the binding size scale. Rotate the
binding lever away from you to close the hooks
until they make contact with the document.
3. Read the line closest to the document follow it
to the right to the corresponding comb binding
element size. This is the comb binding element
size required to bind the document. Your
CombBind C-110e can bind books up to 300
sheets. Or 1-1/2" (38mm). For best results,
always use GBC brand covers with GBC color-
coordinated binding combs.
E. BINDING (see figure 4)
1. Place the plastic comb binding element behind
the vertical comb with the open portion of the
element facing you.
2. Rotate the binding lever toward you until the
comb binding element opens sufficiently to
insert your document.
3. Place the front cover (finished side down) onto
the opened binding element fingers. Place the
document pages (face down) onto the element.
Repeat for larger documents as required. Place
the back cover (finished side up) on the open
binding element fingers last.
4. Rotate the binding lever away from you, back to
its original position to close the binding element.
will
5. Remove the book by lifting upward. Your
document is now complete.
6. Once you become familiar with your CombBind
C-110e you will find that you can bind as you
punch, increasing your productivity.
F. EMPTY CHIP DRAWER: (see figure 2 & 5)
1. Your CombBind C-110e has a chip drawer
located on the right side of the machine (see figure 5).
When it is full of punched paper chad a red light
(see figure 2) will illuminate. Gently pull the drawer
to open it and remove from machine, empty and
re-insert the drawer back in machine until it snaps
in place.
G. SERVICE
1. Contact an authorized GBC service
representative for any required repairs.
11.7" (297mm - A4)
15 sheets (20 lb./80gsm)
300 sheets (1-1/2"/38mm)
20 lbs. (9.1 kg.)
16" (406mm) x 14" (356mm) x 9" (229mm)
10