Rear Panel - Fender BASSBREAKER 45 Mode D'emploi

INPUT POWER
PARALLEL
120V 60Hz
SPEAKER OUTPUTS
350W
45 WATTS 4Ω min TOTAL
MAIN
TYPE: PR 3614
SPEAKER
SERIAL NUMBER
MUTES
INTERNAL
FUSE
SPEAKER
F3AL
250V
L. IEC POWER INLET: Using the included power cord, connect to a
grounded outlet in accordance with the INPUT POWER voltage and
frequency specified at the power inlet.
M. FUSE: Provides electrical over-current protection. With power
disconnected, replace a blown fuse only with one of the type and
rating specified on the amp's rear panel.
N. PARALLEL SPEAKER OUTPUTS: Connect external speaker enclosures
here. For the Bassbreaker 45 combo, to use an external speaker enclo-
sure in combination with the internal speakers, plug external enclosure
into EXTENSION SPEAKER. To use an external speaker enclosure only,
plug external enclosure into MAIN SPEAKER (internal speakers will
automatically be disconnected).For the Bassbreaker 45 amp head, use
the MAIN SPEAKER jack when using only one enclosure (there will be
no sound if the MAIN SPEAKER jack is not used). See tables at right for
acceptable parallel speaker enclosure impedance combinations for the
Bassbreaker combo (above) and head (below) models.
O. IMPEDANCE SELECT: If no external enclosures are connected to
PARALLEL SPEAKER OUTPUTS (N), this switch should be set to the 16Ω
position. To avoid damage when using PARALLEL SPEAKER OUTPUTS,
this switch must be set in accordance with total impedance load as
shown in the tables at right for the Bassbreaker combo (above) and
head (below) models.
Using two speaker enclosures of different impedance ratings is not rec-
ommended. If using enclosures with different ratings, set IMPEDANCE
SELECT switch (O) to the lower of the two speaker enclosure ratings.

When using both speaker jacks, do not use an enclosure rated at less
than 4Ω. When using MAIN SPEAKER jack alone, do not use an enclo-
sure rated at more than 16Ω.
To avoid damaging the amp, put it in STANDBY mode (J) or turn it
!
off (K) when changing speaker connections and IMPEDANCE SELECT
switch (O) settings.
TYPE
POWER
IMPEDANCE
SPEAKERS (INTERNAL)
EXTERNAL SPEAKER ENCLOSURE
TUBES
ACCESSORIES
DIMENSIONS (COMBO)
DIMENSIONS (HEAD)
WEIGHT (COMBO)
WEIGHT (HEAD)

Rear Panel

4Ω - 8Ω -16Ω
EXTENSION
IMPEDANCE
SPEAKER
SELECT
Specifications
PR 3614
Requirements: 350 watts
1MΩ (all inputs)
Two 12" Celestion® G12V-70 (8Ω each, 16Ω total, combo model)
Bassbreaker BB-212 (optional, PN 226800000, contains same speakers as combo model)
V1-V3: 7025/12AX7A/ECC83
Combo cover (included, PN 7706657000)
Width: 26.22" (66.6 cm)
Width: 26.22" (66.6 cm)
55 lbs. (25 kg)
32 lbs. (14.5 kg)
Product specifications subject to change without notice.
BASSBREAKER 45
FENDER MUSICAL INSTRUMENTS CORP.,
CORONA, CA U.S.A.
MADE IN MEXICO
Bassbreaker 45 combo acceptable parallel speaker enclosure impedance
combinations with correct IMPEDANCE SELECT switch (O) settings:
INTERNAL SPEAKER MAIN SPEAKER EXTENSION SPEAKER
16Ω NONE
16Ω NONE
DISCONNECTED* 16Ω
DISCONNECTED* 8Ω
DISCONNECTED* 4Ω
DISCONNECTED* 16Ω
DISCONNECTED* 8Ω
*NOTE: When a plug is inserted into MAIN SPEAKER jack, internal speaker load (16Ω) is auto-
matically disconnected and does not affect total impedance load.
Bassbreaker 45 amp head acceptable parallel speaker enclosure imped-
ance combinations with correct IMPEDANCE SELECT switch (O) settings:
MAIN SPEAKER EXTENSION SPEAKER
16Ω
8Ω
4Ω
16Ω
8Ω
For questions and troubleshooting, contact a Fender
specialist at:
1-800-856-9801 (U.S. toll free)
1-480-596-7195 (International)
Output: One to 45 watts (adjustable) into 16Ω/8Ω/4Ω
V4-V5: EL34
Amp head cover (included, PN 7706658000)
Height: 22" (55.9 cm)
Height: 10.75" (27.3 cm)
TM
A PRODUCT OF:
IMPEDANCE SELECT
NONE 16Ω
16Ω 8Ω
NONE 16Ω
NONE 8Ω
NONE 4Ω
16Ω 8Ω
8Ω 4Ω
IMPEDANCE SELECT
NONE 16Ω
NONE 8Ω
NONE 4Ω
16Ω 8Ω
8Ω 4Ω
Depth: 10.5" (26.7 cm)
Depth: 8.5" (21.6 cm)
3