Technical Specifications; Setup And Assembly - Thomashilfen tRide Instructions D'utilisation

Technical specifications

Seat depth
Seat width
Back height*
Lower leg length
Hip angle
Knee angle
Foot angle
Height adjustment arm support
Seat tilt - in-space
Size of arm suport(w x h)
Seat height
Size of footrest (w x d)
Overall dimensions of seat unit (l x w x h)
Folded dimensions of seat unit (l x w x h)
Weight (seat)
Push bar height
Overall dimensions
of chassis in running order (l x w x h)
Folded dimensions of chassis (l x w x h)
Overall dimensions of the tRide rehabilitation stroller,
ready for use (l x w x h)
Folded dimensions of the tRide rehabilitation
stroller (l x w x h)
Wheel size (front (swivel wheels))
Wheel size (rear)
Weight (chassis without seat unit)
Carring capacity (seat)
Carring capacity (chassis)
*without headreast

Setup and assembly

Settings/adjustments may only be undertaken by specialists that have received the requisite training or instruction (e.g.
a medical product consultant at a medical appliance specialist dealership).
Fitting/removal of accessories is carried out using commercially available standard tools. Separate assembly and
operating instructions are supplied with each accessory. If you do not have these instructions you can download them
at any time from the download page of our website at www.thomashilfen.de
Unfolding
Hold the rehabilitation stroller by its push handle, place your foot on the rear axle and then pull the handle upwards
(until the push handle audibly clicks into place) (fig. 1). If necessary, tilt the seat to the horizontal position (see "Adjusting
the seat tilt angle"). Then bring the backrest into the upright position (release the locking lever on the back of the seat
unit). The footrest must be secured at the toggle joints. To do this, place the ratchet joints one above the other and secure
with the screws (fromthe inside), the washers (from the outside) and the wing nuts (from the outside).
Folding
Bring the backrest into the prone position, release the toggle joints and swing the footrest towards the seat unit. Tilt the
seat to the horizontal position (see "Adjusting the seat tilt angle") and then release the locking levers (pull upwards)
located on both sides of the subframe while at the same time pushing the push handle downwards and inwards toward
the frame (fig. 2).
CAUTION: Hold the frame securely – do not allow it to fall. Do not apply the foot brake; otherwise
there is a risk of deforming the wheels.
Note on folding: Ensure that the seat is always in the horizontal position when folding your tRide.
tRide 1
17 - 28 cm / 6.7 - 11"
20 - 30 cm / 7.9 - 11.8"
26 - 42 cm / 10.2 - 16.5"
17 - 30 cm / 6.7 - 11.8"
90° to 140°
90° to 180°
78° to 100°
10 - 14 cm / 3.9 - 5.5"
-10° bis +35°
21 x 10 cm / 8.3 x 3.9"
46 cm / 18.1"
29 x 18 cm / 11.4 x 7.1"
85 x 41 x 57 cm
33.5 x 16.1 x 22.4"
63 x 36 x 38 cm
24.8 x 14.2 x 15"
8,8 kg / 19.4 lbs
76 - 117 cm / 29.9 - 46.1"
75 x 60 x 77 cm /
29.5 x 23.6 x 30.3"
79 x 60 x 38 cm
31.1 x 23.6 x 15"
90 x 60 x 101 cm
35.4 x 23.6 x 39.8"
81 x 60 x 63 cm
31.9 x 23.6 x 24.8"
7,5"
10"
8 kg / 17.6 lbs
35 kg / 77.2 lbs
45 kg / 99.2 lbs
tRide 2
24 - 35 cm / 9.4 - 13.8"
26 - 35 cm / 10.2 - 13.8"
32 - 52 cm / 12.6 - 20.5"
25 - 36 cm / 9.8 - 14.2"
90° to 140°
90° to 180°
78° to 100°
12 - 18 cm / 4.7 - 7.1"
-10° bis +35°
29 x 12 cm / 11.4 x 4.7"
47 cm / 18.5"
33 x 21 cm / 13 x 8.3"
98 x 46 x 46 cm
38.6 x 18.1 x 18.1"
76 x 46 x 50 cm
29.2 x 18.1 x 19.7"
10,8 kg / 23.8 lbs
81 - 120 cm / 31.9 - 47.2"
81 x 67 x 79 cm
31.9 x 26.4 x 31.1"
83 x 67 x 38 cm
32.7 x 26.4 x 15"
110 x 67 x 99 cm
43.3 x 26.4 x 39"
79 x 67 x 72 cm
31.1 x 26.4 x 28.4
7,5"
10"
9 kg / 19.8 lbs
40 kg / 88.2 lbs
50 kg / 110.2 lbs
17