Read This First - Hapro Luxura V7 Mode D'emploi

Masquer les pouces Voir aussi pour Luxura V7:
Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Note:
Please consult enclosed tanning
schedule for advised tanning
times.
Repairs may only be carried out
by qualified personnel.
Always disconnect the main
power at the circuit breaker
before servicing or repairing
the unit.
Everything regarding assembl y , instructions and other details contained in this manual must be
followed correctl y and entirel y . Failure to do so correctl y or entirel y will render the right to any product
warranty or liability on the supplier's behalf null and void. If there is any uncertainty as to whether
the instructions contained in this manual have been followed properl y and entirel y , you should contact
1 Contact your authorised Hapro dealer immediatel y if this
unit does not function as outlined in this manual.
2 Do not operate this unit in humid spaces.
3 Al w ays make sure the fuses can carry the load. This unit
has to be protected by ground fault circuit interrupter
(GFCI) of 0.03A.
4 Al w ays disconnect the power to the unit at the wall
breaker (isolator) when servicing or cleaning the in-side
construction of the cabine. Maintenance for which the
procedure is not described in this manual should onl y
be carried out by a qualified electrician. Never clean the
electrical components with fluids.
5 Ensure that the canopy does not touch the wall when
opened.
6 Prevent the acrylic sheets from coming into contact with
sharp objects.
7 This unit may not be operated if:
• the user is not wearing protective uv-goggles
• the blue or white facial glass is cracked or broken
• the acrylic panel in the canopy and/or bench is missing
• one or more of the fans in the unit are not functioning
properl y
• the timing mechanism is not functioning properl y
• the temperature inside the cabin is 30°C or higher
8 To ensure maximum tanning effectiveness, change the
acrylic sheet after every 1200 hours of operation.
9 To ensure maximum tanning effectiveness, replace
the lamps and the facial tanning lamps according to
manufacturer´ s instructions.
10 Check local regulations to find out the proper procedure
for lamp disposal.
11 Note: onl y a special acrylic cleaner may be used to clean
the acrylic sheet. Never use cleaners that contain alcohol,
as these can damage the acrylic sheet.
12 The UV-type of the tanning unit is indicated on the
specification sticker.
- 6 -

Read this first

the supplier of the sunbeds.
13 Ultraviolet radiation from the sun or UV appliances can
cause skin or eye damage. These biological effects depend
upon the quality and quantity of the radiation as well as
the skin and eye sensitivity of the individual.
14 Excessive exposure may cause skin to burn. Excessive
repeated exposure to ultraviolet radiation from the sun or
UV appliances may lead to premature ageing of the skin
as well as increase risk of skin tumours.
15 The unprotected eye may develop surface inflammation
and in some cases, after a cataract operation for example,
damage may accur to the retina after eccessive exposure.
Cataracts may develop after prolonged exposures.
16 If the suppl y cord is damaged, it must be replaced by
the manufacturer or service agent or a similarl y qualified
person in order to avoid a hazard.
17 To replace lamps and starters, remove by turning a quarter
turn to the left. Placement of new lamps and starters is
done in the reverse to the above mentioned procedure.
18 When installing the equipment, follow the recommended
minimum distances listed in the "Dimensions / Placement"
chapter.
19 Clean the dust filters after every 50 hours of use.
Regularl y check the dust filters.
20 Children should be supervised to ensure that they do not
play with the tanning unit.
21 Non-users, especiall y children, must not be present when
the appliance is being operated.

Publicité

Table des Matières
loading

Table des Matières