Milwaukee 48-22-8510 Manuel De L'utilisateur page 4

Installing the Chest onto the Cabinet
CAUTION
Two people may be required
to complete installation.
1. Remove the cabinet mat from the rolling cabinet.
The top chest will not line up with the brackets if
the mat is in place.
2. Place the top chest on top of the rolling cabinet.
NOTE: The holes in the cabinet are tapped and do
not require nuts.
3. Attach the two brackets to the back of the product
to secure the top chest to the rolling cabinet.
Place the brackets over the holes and secure
with four screws (DD) per bracket.
4. Tighten all screws securely with a Phillips
screwdriver.
DD
Installing the Drawer Liners and Mat
Place the drawer liners in appropriately sized
drawers and the mat in the chest lid area to protect
the surface.
Installing the Bumpers
Attach the four bumpers to the rolling cabinet using
two screws (EE) per bumper.
EE
Installing the Cord Storage Brackets
Attach the brackets to the back of the chest and
cabinet with two screws (DD) per bracket. Orient
the brackets with one pointed up and one pointed
down so that the power outlet cord can be wrapped
around the brackets for storage.
OPERATION
WARNING
To avoid injury or property
damage, do not exceed maximum shelf capac-
ity. Use care when moving chest/cabinet on
incline or rough surface. Chest/cabinet may
tip if weight is not evenly distributed front to
back and side to side. Place more than half
the total load weight on the bottom cabinet
when possible.
Locking and Unlocking the Chest/Cabinet
NOTE: The drawers must be fully closed before
locking/unlocking the unit.
Insert the key. Turn it fully left to lock, or fully right
to unlock. Always remove the key after locking
and unlocking.
Moving the Chest/Cabinet on an Incline or
Rough Surface
Take care that the chest/
cabinet does not tip or
become unbalanced when
moving it on an incline
or rough surface. Do not
exceed an incline of 10
degrees. Lock the chest/
cabinet and secure all
items before moving.
Using the Caster Brakes
To lock the swivel casters, step down on the le-
vers marked Lock. Be sure to lock both casters to
prevent chest/cabinet from rolling or swiveling. To
unlock casters, push down on the levers marked
Unlock.
Rolling the Chest/Cabinet
The chest/cabinet is only intended for rolling short
distances. Only roll the chest/cabinet using the
handle. Do not push or pull chest/cabinet by the
frame or product may tip. Do not modify the chest/
cabinet in any way. Drilling holes or modifying the
chest/cabinet will lower the load capacity, which
can cause the chest/cabinet to collapse, resulting
in injury. Lock the chest/cabinet and secure all items
before rolling.
Lifting the Chest/Cabinet
The cabinet and chest/cabinet combo are not
intended to be lifted. However, if you need to lift,
empty the chest/cabinet and then place straps or
forks inside and next to casters. Do not lift loaded
chests/cabinets. Be sure all bystanders are moved
away before lifting chest/cabinet.
6
Mounting Chargers
The rolling cabinet comes equipped with four pre-
installed charger mounting bosses, located below
the power strip. The charger mounts are suitable
for holding MILWAUKEE M18™ & M12™ Multi
Voltage chargers as well as M18™ chargers. To
mount a charger, install a screw (DD) into each
boss, then slide the charger's key-hole slots over
the screws. Slide the charger toward the fl oor to
lock it onto the screws.
Removing the Drawers
1. Fully extend and empty the drawer.
2. Depending on the side, either lift or lower the
release lever on both sides so the slides can ride
over the stops. Pull out to remove.
Release Lever
Installing the Drawers
1. Pull the slides and slide carrier out until fully
extended.
2. Hold the slide on the cabinet while aligning it with
the slide on the drawer.
3. Slightly insert one side and repeat for the other
side.
4. Slowly push the drawer until it is fully closed to
engage the slide.
5. Open and close the drawer to verify proper
operation.
MAINTENANCE
WARNING
To reduce the risk of injury,
contact MILWAUKEE Corporate After Sales
Service Technical Support for ALL repairs and
replacement parts.
Maintaining the Chest/Cabinet
Keep your chest/cabinet in good repair by adopting
a regular maintenance program. Before use, ex-
amine the general condition of your chest/cabinet.
Check for loose screws, misalignment, binding of
wheels, broken parts and any other condition that
may affect its safe operation. Do not use a dam-
aged chest/cabinet.
Maintaining the Casters
Grease the casters annually using high quality
bearing grease.
Grease
Points
Maintaining the Drawers
1. Periodically clean the drawer trim, and inside the
drawers with a mild detergent and water.
2. Remove grease and oil in drawer with a standard,
nonfl ammable cleaning fl uid.
3. The use of drawer liners is recommended to
protect the fi nish inside the drawers and make
the drawers easier to clean. Drawer liners can
be cleaned with soap and water.
4. Lubricate the slides semi-annually with general
purpose grease or equivalent.
Grease
Points
7