Operating The Toaster; Power Save Mode - Hatco Toast-Qwik ITQ Série Manuel D'installation Et D'utilisation

English

Operating the Toaster

Startup
1. Make sure the toaster is plugged into a properly grounded
electrical outlet of the correct voltage, size and plug
configuration. See the SPECIFICATIONS section for
details.
2. Move the power I/O switch
located on the back of the
toaster to the "I" (on) position.
• Graphics and software
version information will
appear on the display.
3. Wait 10 seconds to allow
the toaster to run internal
diagnostics.
Product Sensors
USB
Port
Warning
Light
Touchpad
Display
Touchpad
Control
Fan Filter
Cooling Fan
Toast Chute
Model ITQ-1000-1C
4. Touch and hold the
on the touchpad control for
three seconds to activate the
toaster.
• "Preheating" will show on
the touchpad display, and
the heating elements inside the toaster will energize.
• The preheating cycle lasts approximately 10 minutes.
When the preheating cycle is complete, the available
menu items will appear on the touchpad display.
5. Touch the appropriate
program key (keys 1–5) on
the touchpad control for the
desired conveyor and menu
item.
• The elements and conveyor
belt will adjust settings to the selected menu item.
Form No. ITQM-0317
Power I/O
Switch
Crumb
Tray
key
Preheating 10:00
1 Bun
2 Toast
3 Hash Brown
4 Product 4
5 Product 5
6. Place food product between the product sensors on the
conveyor belt.
• The product sensors detect the presence of the food
product.
• For menu items that include two-directional or custom
conveyor belt movement, the sensors signal the toaster
to begin the toasting sequence.
• Change the toasting shade
of the food product any
time by touching either the
or keys up to five
times.
7. Change the selected menu item at any time by touching
the desired program key on the touchpad control.
NOTE: If the Warning light comes on, the unit may be overheating
due to fan failure/blockage. Turn off and unplug the unit.
Refer to the "Cleaning the Fan Filters" procedure in the
MAINTENANCE section of this manual. If the unit does
not function properly after cleaning the fan filters, contact
an Authorized Service Agent or Hatco for assistance.
Standby Shutdown
Use standby shutdown to put the toaster in standby during
extended periods of non-use.
1. Touch and hold the
three seconds to shut down operation and put the toaster
into standby.
• The heating elements and
conveyor(s) will shut down.
• The cooling fans will run for
20 minutes to cool the unit.
Shutdown
1. Touch and hold the
three seconds to shut down operation and put the toaster
into standby.
2. After the cooling fans stop, move the power I/O switch
located on the back of the unit to the "O" (off) position to
turn off the toaster. NOTICE: Do not turn off unit while
cooling fans are running. Damage to unit may occur.

Power Save Mode

All ITQ series toasters have a built-in Power Save mode.
This feature significantly reduces heat levels and energy
consumption when the toaster has not been used for a specified
period of time or when activated by the operator.
To start Power Save mode manually during operation:
1. Touch the
• The conveyor belt will
speed up temporarily to
clear product from toaster.
• "Power Save" will show on
the touchpad display.
To exit Power Save mode:
1. Touch any of the program keys (keys 1–5) or place food
product between the product sensors on the conveyor belt.
The unit will be ready to toast in approximately two minutes
or less (a countdown will appear on the touchpad display).
9
OPERATION
1 Bun
2 Toast
3 Hash Brown
4 Product 4
5 Product 5
2X Lighter
key on the touchpad control for
Cooling fans on.
Leave plugged in.
key on the touchpad control for
key.
Power Save
Caution Hot