Using The Systems Menu; Updating Software - Hatco Toast-Qwik ITQ Série Manuel D'installation Et D'utilisation

English

Using the Systems Menu

The Systems menu consists of a list of toaster configuration
and service functions. Most of these functions are for service
technician or factory use only.
Systems Menu Functions
Toaster options ........Standby heat—Heat output level
(percentage) of the elements during
Power Save mode.
Standby time—Length of time (minutes)
the toaster can be idle before Power
Save mode starts automatically.
Staging mode—YES = Toaster performs
a single toasting sequence, then stops
until a new toasting sequence is started
manually. NO = Conveyor moves
forward continuously. Operator use,
see procedure.
Service info ..............Displays all errors codes that have
occurred. Service technician use only.
Operation statistics .Displays operational information about
toaster such as "on" time, element use,
motor use, etc. Service technician use
only.
LCD options .............Adjusts screen resolution. Service
technician use only.
Software Update ......Updates toaster software/custom menu
items in conjuction with a USB flash
drive. Operator use, see procedure.
Factory calibration ..Used for factory adjustments. Factory/
Service technician use only.
Test mode .................Used for troubleshooting. Service
technician use only.
Changing Toaster Options
1. Perform steps 1–4 of the "Startup" procedure listed
previously in this section.
2. Touch and hold the POWER SAVE key for three seconds
(this can be done during the preheating cycle).
• The Systems menu will appear on the display.
3. Use the left-side
and touch the left-side "5" program key to select.
• A password prompt will appear:
For single conveyor units, touch the "6" program key for
the password, and touch the "5" program key to accept.
For dual conveyor units, touch the right-side "1" program
key for the password, and touch the left-side "5" program
key to accept.
• The toaster options "Standby heat", "Standby time", and
"Staging mode" will appear on the display.
NOTE: Dual conveyor units will show toaster options for each
conveyor designated by "L" (left) and "R" (right).
4. Use the left-side
select the desired toaster option.
5. With the option highlighted, use the right-side
to change the parameter.
6. Continue to use the left side
and highlight/select other desired options, followed by the
right-side keys to change the parameter.
Form No. ITQM-0317
keys to scroll to Toaster options,
keys to scroll through and highlight/
keys to scroll through
Touchpad Display
Touchpad Control
for single
conveyor units.
Program
Keys 1–5
Touchpad Control and Display (ITQ-875-1C and ITQ-1000-1C)
7. When all desired options have been updated:
• For single conveyor units: Touch the "5" program key to
save the changes; Touch the "10" program key to cancel
all changes.
• For dual conveyor units: Touch the left-side "5" program
key to save the changes; Touch the right-side "5"
program key to cancel all changes.

Updating Software

1. Perform steps 1–4 of the "Startup" procedure listed
previously in this section.
2. Touch and hold the POWER SAVE key for three seconds
(this can be done during the preheating cycle).
• The Systems menu will appear on the display.
3. Use the left-side
and touch the left-side "5" program key to select.
• A password prompt will appear:
For single conveyor units, touch the "6" program key for
the password, and touch the "5" program key to accept.
For dual conveyor units, touch the right-side "1" program
key for the password, and touch the left-side "5" program
key to accept.
4. Remove the cover from the USB port located near the
touchpad control.
5. Insert the designated USB flash drive into the USB port.
6. Touch the left-side "5" program key to start the software
update.
• The software update will begin and last approximately
20 seconds. NOTICE: Do not remove the flash drive
or turn off the toaster during a software update.
• When the display returns to the main startup screen
showing the company logo and software version
keys
information, the update is complete. It is now safe to
remove the flash drive.
7. Replace the cover on the USB port.
11
OPERATION
1 Bun
2 Toast
3 H. Brown
4 Product4
5 Product5
keys to scroll to Software Update,