Warnings; Power; Safety Precautions; Installation Precautions - Urmet 1092 Manuel D'utilisation

5.3

WARNINGS

5.3.1

POWER

 Only use the power unit provided to power the device. Check mains rating before plugging the power unit in.
 Do not pull the cable to unplug the device.
5.3.2

SAFETY PRECAUTIONS

 Keep the device away from rain and humidity to prevent risk of fire and electrocution. Do not introduce material
(solid or liquid) inside. If this should accidentally occur, disconnect the device from the mains and have it inspected
by qualified personnel.
 Never open the device. In all cases, contact a qualified personnel or authorised service centre for repairs.
 Keep the device away from children, to prevent accidental damage.
 Do not touch the device with wet hands to prevent electrical shock or mechanical damage.
 Do not use the device if it should fall or the external casing is damaged. Risk of electrocution if the device is used
in such conditions. Contact the retailer or authorised installer.
 It is advisable to disconnect the power wire if the monitor is not used for a certain time.
5.3.3

INSTALLATION PRECAUTIONS

 To prevent overheating the device, arrange it in a position allowing the flow of air through the slots in the casing.
Ensure at least 5 cm of free space when installing inside a rack. For the same reason, do not install sources of
heat, such as radiators or hot air ducts. Keep away from direct sunlight. Do not install in areas subject to excessive
dust, mechanical vibrations or shocks.
 Do not arrange this device on an unstable surface, such as a tottering or slanted table. The device could fall
causing injury or mechanical failures.
 Do not install the device in a place where it could be exposed to humidity or water. Do not direct a jet of water
onto the device: risk of fire, electrocution or mechanical failure.
 Stop using the device if water or other material should penetrate inside: risk of fire and electrocution. Contact the
retailer or authorised installer.
Slots and openings in the cabinet are provided for ventilation. These openings must not be blocked or covered.

Do not place heavy or heat generating objects on top of the device: this could damage the casing and/or increase

internal temperature causing faults.
 Do not cover the device with a cloth while it is running to prevent deforming the external casing and overheating
the internal parts: risk of fire, electrocution and mechanical failure.
 Keep magnets and magnetised objects away from the device to prevent faults.
 Do not use the device in presence of smoke, vapour, humidity, dust or intense vibrations.
 Wait for a while before operating a device immediately after transporting it from a cold place to a warm place and
vice versa. Wait on average for three hours: this will allow the device to adapt to the new ambient (temperature,
humidity, etc.).
 The monitor is provided with a plastic base and rubber feet. It can be positioned on a horizontal surface, such as
a desk or a table. Make sure that the device is fastened firmly and that it is not resting on unstable supports or
surfaces. Dropping could cause severe injury and damage the device.
 Remember to adjust the brightness and contrast to obtain a perfect image.
 The monitor can also be instalLCD on the wall by means of a bracket (not provided).
5.3.4

CLEANING THE DEVICE

 Rub delicately with a dry cloth to remove dust and dirt.
 Dip the cloth in neutral detergent if dirt cannot be eliminated with a dry cloth alone.
 Do not use volatile liquids (such a petrol, alcohol, solvents, etc.) or chemically treated clothes to clean the device
to prevent deformation, deterioration or scratches to the paint finish.
5.3.5

PRIVACY AND COPYRIGHT

 The 1092/401 LCD monitor is a device for CCTV systems. Recording of images is subject to the laws in force in
your country. Recording of images protected by copyright is forbidden.
 Product users shall be responsible for checking and respecting all local rules and regulations concerning
monitoring and recording video signals. The manufacturing SHALL NOT BE LIABLE for use of this product not in
compliance with the laws in force.

DS1092-181A 14