Product Dimensions; Cabinet Dimensions - Jenn-Air JDS9860 Instructions Pour L'installation

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Product Dimensions

Model JDS9860
G
F
A. 30³⁄₄" (78.1 cm)
B. 23" (58.4 cm) countertop notch to
rear of cooktop
C. Gas information plate (located on
the right-hand side of the bottom
oven frame)
D. Model/serial number plate (located
on the right-hand side of the
bottom oven frame)
Model JDS9865
NOTE: Cooktop shown may differ from your model.
A
G
F
A. 30⁷⁄₈" (78.4 cm)
B. 35³⁄₄" (90.8 cm) height to
underside of cooktop edge
with leveling legs screwed all
the way in*
C. Model/serial number plate
(located behind the storage
drawer on the right-hand side
of the oven frame)
A
B
E
E. 29" (73.4 cm) from handle
to back of range**
F. 29⁷⁄₈" (75.9 cm)*
G. 35³⁄₄" (90.8 cm) height to
underside of cooktop
edge with leveling legs
screwed all the way in*
B
C
D
E
D. 29⁷⁄₈" (75.9 cm)
E. Gas information plate (located
behind the storage drawer on
the left-hand side of the oven
frame)
F. 29" (73.7 cm) from handle to
back of range**
G. 27" (68.6 cm) from handle to
rear of cooktop
*Range can be raised approximately 1" (2.5 cm) by adjusting the
leveling legs.
**When installed in a 24" (61.0 cm) base cabinet with
25" (63.5 cm) countertop; front of oven door protrudes
5" (12.7 cm) beyond 24" (61.0 cm) base cabinet.

Cabinet Dimensions

Cabinet opening dimensions shown are for 25" (64.0 cm)
countertop depth, 24" (61.0 cm) base cabinet depth and
36" (91.4 cm) countertop height.
Range may be installed with zero clearance to combustible
construction at the rear and on the sides below the cooktop.
C
C
D
D
H
A. 13" (33.0 cm) upper cabinet depth
B. 30" (76.2 cm) min. opening width
C. For minimum clearance to the top of the cooktop, see NOTE.
D. 23¹⁄₄" (59.1 cm) opening depth
E. 30" (76.2 cm) min. opening width
F. Electrical and gas supply - 5½" (14.0 cm) min. from either cabinet,
10" (25.4 cm) max. from floor. Nothing located in shaded area can
extend more than 2¼" (5.7 cm) from back wall or range will not slide
all the way back. Grounded outlet must be flush mounted.
G. Cabinet door or hinge should not extend into cutout.
H. 18" (45.7 cm)
I. 3" (7.6 cm) min. clearance from both sides of the range to the side
wall or other combustible material.
NOTE: 24" (61.0 cm) minimum when bottom of wood or metal
cabinet is shielded by not less than ¹⁄₄" (0.64 cm) flame retardant
millboard covered with not less than No. 28 MSG sheet steel,
0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or
0.020" (0.5 mm) copper.
30" (76.2 cm) minimum clearance between the top of the cooking
platform and the bottom of an uncovered wood or metal cabinet.
A
B
C
D
E
I
F
G
I
5

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Jds9865

Table des Matières