Ecoflam MAX GAS 170 P Notice D'emploi page 6

EN
Contents
- Index - General warnings - Conformity declaration
Overview
Contents
Function
Installation
Start up
Service
Overview
Important notes
MAX GAS 170-250 P burners are
designed for the low-pollutant combustion
of natural gas and Liquefied Petroleum
Gas. The design and function of the
burners comply with standard EN676.
Assembly and commissioning must be
carried out only by authorised specialists
and all applicable guidelines and directives
must be observed.
Burner description
MAX GAS 170-250 P are single-stage,
fully automatic, monoblock type burners.
The special design of the burner head
provides low-polluting combustion with
high efficiency. In line with testing as
defined by EN676, the values comply
with emissions class 3 (NOx<80mg/kWh)
Emissions values may differ, depending on
combustion chamber dimensions,
combustion chamber load and the firing
system (three-pass boilers, boilers with
reverse firing).
They are suitable for use with all heat
generators complying with EN 303 or for
use with hot air generators complying with
DIN 4794, and DIN 30697 within their
respective performance range.
Ecoflam burners have been designed and built in compliance with all current regulations
and directives.
All burners comply to the safety and energy saving operation regulations within the standard
of their respective performance range. The quality is guaranteed by a quality and management
system certified in accordance with ISO 9001:2008.
6 www.ecoflam-burners.com
Technical data
Working diagrams
Dimensions
Index
General warnings
Conformity declaration
Burner description
General safety functions
E-BCU GAS control and safety unit
Burner assembly
Electrical connection
Checks before commissioning
Adjusting burner output
Air pressure switch adjustment - setting gas pressostat
Maintenance
Troubleshooting
Gas pressure diagrams
Electrical diagrams
Spare parts list
Use for any other application requires the
approval of Ecoflam.
The following standards should be
observed in order to ensure safe,
environmentally sound and
energy-efficient operation:
EN 676
Forced-draught gas burners
EN 226
Connection of fuel oil and forced-draught
gas burners to a heat generator.
EN 60335-1, -2-102
Specification for safety of household and
similar electrical appliances, particular
requirements for gas burning appliances.
Installation location
The burner must not be operated in rooms
containing aggressive vapours (e.g. spray,
perchloroethylene, hydrocarbon
tetrachloride, solvent, etc.) or tending to
heavy dust formation or high air humidity.
Adequate ventilation must be provided at
the place of installation of the furnace
system to ensure a reliable supply with
combustion air.
3
Declaration of conformity
for gas burners
4
5
We,
Ecoflam Bruciatori S.p.A.
6
6
declare under our sole responsibility
6
that the gas burners named
7
MAX GAS
8
9 conform to the following standards:
EN 676
10
EN 55014-1
11
EN 60335-1
EN 61000-6-2
11
These products bear the CE mark in
12
accordance with the stipulations of the
13
following directives:
2014/35/UE Low Voltage Directive
14
2014/30/UE EMC Directive
2006/42/EC Machine directive
15
2011/65/EU RoHS2 directive
2009/142/CEE Gas Appliance
56-57
Directive
58
59-61
Variations may arise as a result of local
regulations.
We can accept no warranty liability
whatsoever for loss, damage or injury
caused by any of the following:
- Inappropriate use.
- Incorrect assembly or repair by the
customer or any third party, including the
fitting of non-original parts.
Provision of the system and the
operating instructions
The firing system manufacturer must
supply the operator of the system with
operating and maintenance instructions on
or before final delivery. These instructions
should be displayed in a prominent
location at the point of installation of the
heat generator, and should include the
address and telephone number of the
nearest customer service centre.
Notes for the operator
The system should be inspected by a
specialist at least once a year. It is
advisable to take out a maintenance
contract to guarantee regular servicing.
420010372902
EN 50156-1
EN 55014-2
EN 60335-2-102
EN 61000-6-3