Siemens SIRIUS 3RW44 2 Série Instructions De Service page 21

Quick commissioning menu, when switching on for the
first-time or after executing command "Factory settings"
Information on quick start menu
After supplying the control voltage for the first time, you will be
automatically directed to the quick start menu. You must
complete the entire quick start menu to commission the soft
starter.
If you confirm the last item "Save settings?" with "yes" in the
quick start menu, you can only return to this menu by resetting
the device back to the basic factory settting. (See manual or
operating instructions)
This overwrites all settings made up until that point.
Information on application selection:
Standard parameters are recommended on the basis of the set
type of application.
If the required load is not listed, choose a fan in order to
preselect the necessary start parameters.
In general:
The parameters are suggested settings.
The parameters may need to be optimized, as explained in the
Section "Start command "Soft starter on".
1. "Soft starter off" 1. "Soft starter off"
2. Increase starting time in 2. Reduce starting time in menu
menu item Settings, or item Settings or if current
3. If current limiting has limiting has been set, increase
been set, possibly reduce the current limiting value.
current limiting value 3. If the torque control is active,
check if the selected limiting
torque is high enough
(recommended ≥ 150 %)
The motor reaches its
nominal rotational
speed
- quicker than desired
- not softly
- if no current limiting
has been set according
Motor:
to the specified ramp
time
Increase DC braking
Decrease
Increase
torque or increase
stopping time stopping
stopping time
time
or decrease
stopping
The
torque
The
motor
motor
does not
The motor Soft
keeps
come to
comes to stopping
going
a stand-
a stop Pump stop
for too
still
abruptly,
long.
not softly.
The water
can be
heard
during the
pumping
operation.
3ZX1012-0RW44-0AA0
Select language
Select application
Set the rated operating
current of the motor
Set starting time
Set current limiting value
Save settings
1. "Soft starter off"
2. Increase the start voltage or
start torque in menu item
Settings or
3. if current limiting has been
set, possibly increase the
current limiting value
The motor
- hums and does not
start immediately
The motor reaches
- does not start at all
its nominal rota-
(motor stuck)
tional speed
- slower than
desired,
- not at all
(motor stuck)
Reduce DC braking
Increase
torque or reduce
dynamic
stopping time
braking torque
The motor
comes to
Yes
a stand-
still but
the brak-
DC braking
ing cur-
rent con-
tinues to
flow.
(Motor
Motor does not
hums
comes to a stand-
when at a
still or continues to
standstill)
run at a constant
speed during the
braking process.
Quick commissioning of
the 3RW44 SIRIUS soft starter
Wiring control
- Control part and
- Performance part
Check and connect the
voltages in the control and
main circuits.
Fault message
on display?
No
Yes
Initial parameterization or starter
in basic factory settings?
No
Check set parameters in Settings > Parameter set > Motor.
Set starting and stopping parameters in Settings > Parameter
set > Starting or stopping settings according to the Table
"Suggested setting for commissioning" on the basis of the
respective application.
Start command "Soft starter on"
1. "Soft starter off"
2. Decrease the start
Fault message
voltage or start torque
in display
in menu item Settings
No
The motor
starts with a
Does the motor
strong sud-
immediately
No
den
start softly?
increase in
torque
Motor:
Yes
the motor reach
its nominal rotational
No speed quickly and within
the desired time?
Increase DC braking
torque or increase
stopping time
Reduce DC braking
No
torque or reduce
Does the motor
stopping time
continue to run during the
braking process at a
The motor
constant speed (no
comes to a
recognizable
standstill
braking effect)?
but the
braking
current
continues to
flow. (Motor
Combined
hums when
braking
at a stand-
still)
No
"Soft starter off"
Correct fault
(for possible faults see 3RW44
system manual, Chapter 7)
Yes
"Soft starter off"
Correct fault
(for possible faults see
3RW44 system manual,
Chapter 7)
Yes
Does
Yes
Switch off soft starter
Which
Coasting down
stopping mode
is selected?
Pump stop,
torque control,
brakes
Motor
comes to a stand-
still as desired
Yes
Save the changed parameters in
the menu item: Settings > Safety
options > Save settings.
End of commissioning
21