Technical Data; Installation - Woodstar SD16V Traduction Des Instructions D'origine

GB
DE FR

6. Technical data

Mains voltage:
Power input:
Stroke rate:
Protection type:
Stroke:
Base area:
Tilting range of table:
Table size:
Length of saw blade approx.:
Reach:
Max. cutting height at 90°:
Max. cutting height at 45°:
minimum size work piece wxh: 100 x 22 mm
maximum size work piece wxh: 400 x 50 mm
Weight:
Operating mode S6 30%:
Continuous operation with idling (cycle time 10
minutes). To ensure that the motor does not become
excessively hot, it may only be operated for 30% of
the cycle at the specified rating and must then be
allowed to idle for 70% of the cycle.
Noise emission values
Sound
Sound values were measured in accordance with
EN 61029.
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Sound pressure level L :
pA
Uncertainty K :
pA
Sound power level L :
WA
Uncertainty K :
WA
The quoted values are emission values and not nec-
essarily reliable workplace values. Although there is
a correlation between emission and immission levels
it is impossible to draw any certain conclusions as
to the need for additional precautions. Factors with
a potential influence on the actual immission level
at the workplace include the duration of impact,
the type of room, and other sources of noise etc.,
e.g. the number of machines and other neighbor-
ing operations. Reliable workplace values may also
vary from country to country. With this information
the user should at least be able to make a better as-
sessment of the dangers and risks involved.
Reduce noise generation and vibration to a mini-
mum!
• Use only equipment that is in perfect condition.
• Maintain and clean the equipment regularly.
• Adopt your way of working to the equipment.
• Do not overload the equipment.
• Have the equipment checked if necessary.
• Switch off the equipment when not in use.
20 GB
220-240 V~/50 Hz
80 W (S1)
120 W (S6 30%)
500 - 1,700 rpm
IP 20
12 mm
630 x 295 mm
0° to 45° to the left
415 x 255 mm
134 mm
406 mm
50 mm
22 mm
12.7 kg
66.9 dB(A)
3 dB(A)
79.9 dB(A)
3 dB(A)

7. Installation

Setting the saw bench, Fig. 3
Setting the angle scale
• Release the star button and bring the saw bench
(Fig. 3, A) to a right angle (Fig. 3, B) in relation to
the saw blade.
• Use a 90° angle tc measure the right angle between
the blade and the bench. The saw blade be 90° to
the angle.
• Close the star button again when the distance
between the blade and the 90° angle is at a
minimum. The bench should then be at 90° to the
saw blade.
• Release the lock screw (Fig. 3, C) and bring the
indicator to the zero position. Fasten the screw.
Please note: the angle scale is a useful piece of
supplementary equip ment, but should not be used
for precision work. Use scrap wood for saw tests,
adjust the bench if neces sary.
Note: The bench should not be on the motor
block, this can cause undesireable noise.
Horizontal saw bench and diagonal cuts, Fig. 3+4
• The saw bench can be positioned into a 450
diagonal position or be left in the horizontal
position.
• You can read off the approximate slope angle
by using the angle scale located under the work
bench. For more exact adjustment, use scrap wood
for some saw tests; adjust the bench if necessary.
Blade guard assembly and hold-down clamp, Fig.
5+6
• Assemble the workpiece holder (Fig. 5, A) to the
clamp (Fig. 5, B) as shown in the image. This must
be fixed first to the machine with the tommy screw
(Fig. 5, C).
• Secure the blade guard with the screw and nut.
Assembly of dust blower, Fig. 7
Screw the flexi-hose into the opening provided and
tighten it hand-tight.
Mounting the saw on a work bench, Fig. 5
• A workbench made from solid wood is betier than
one made of plywood, as interfering vibrations and
noise are more noticeable with plywood.
• The necessary tools and small parts for assembling
the saw on a workbench are not supplied with
the saw. However, use equipment of at least the
following size:
1 Saw body
2 Foam rubber base
3 Work bench
4 Flat seal
5 Washer (7 mm)
6 Hexagonal nut (6 mm)
7 Lock nut (6 mm)
8 Hexagon head screws (6 mm)