1. Manuels
  2. Marques
  3. Arrow Manuels
  4. Agrafeuses
  5. CT50
  6. Guide d'utilisation

Arrow CT50 Guide D'utilisation

Masquer les pouces
Table des Matières
Les langues disponibles

Les langues disponibles

Liens rapides

Télécharger ce manuel
Instruction Manual
Manual de
instrucciones
Guide d'utilisation
PMCT50-8 Rev 907
GENERAL SAFETY RULES
WARNING! Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire, and / or serious injury. When
using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electrical shock and personal injury. Read the fol-
lowing rules for safe operation before use.
1. WORK AREA: Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. Do not operate power tools in explosive
atmospheres, such as in the presence of flammable liquids, gases, or dust. Power Tools create sparks which may ignite the dust or fumes. Keep bystanders,
children, and visitors away while operating a power tool. Distractions can cause you to lose control.
2. ELECTRICAL SAFETY: Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never
remove the grounding prong or modify the plug in any way. Do not use any adapter plugs. Check with a qualified electrician if you are in doubt as to whether
the outlet is properly grounded. if the tools should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away
from user. Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electrical shock if your
body is grounded. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electrical shock. Do not abuse the
cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges, or moving parts. Replace damaged
cords immediately. Damaged cords increase the risk of electric shock. When operating a power tool outside, use an outdoor extension cord marked "W-A" or
"W". These cords are rated for outdoor use and reduce the risk of electric shock.
3. PERSONAL SAFETY: Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use tool while tired or under the
influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes,
jewelry, or long hair can be caught in moving parts. Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger on the
switch or plugging in tools that have the switch on invites accidents. Remove adjusting keys or switches before turning tool on. A wrench or key that is left
attached to a rotating part of the tool may result in personal injury. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance
enables better control of the tool in unexpected situations. Use safety equipment. Always wear eye protection. Dust mask, non skid safety shoes, hard hat, or
hearing protection must be used for appropriate conditions.
4. TOOL USE AND CARE: Use clamps or other practical ways to secure and support the workpiece to a stable platform. Holding the work by hand or against
your body is unstable and may lead to loss of control. Do not force tool. Use the correct tool for your application. The correct tool will do the job better and
safer at the rate for which it was designed. Do not use tool if the switch does not turn it on or off. Any tool that cannot be controlled with the switch is
dangerous and must be repaired. Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool. Such
preventative safety measures reduce the risk of starting the tool accidentally. Store idle tools out of the reach of children and other untrained persons. Tools
are dangerous in the hands of untrained users.
SAVE THESE INSTRUCTIONS READ ALL SAFETY INSTRUCTIONS BEFORE USE!
www.arrowfastener.com
1
CT50™
Table des Matières
loading

Manuels Connexes pour Arrow CT50

Sommaire des Matières pour Arrow CT50

  • Page 9: Consignes Générales De Sécurité

    Guide d’utilisation CT50™ www.arrowfastener.com PMCT50-8 Rev 907 CONSIGNES GÉNÉRALES DE SÉCURITÉ Attention! Lire attentivement toutes les directives. Le non-respect des directives ci-dessous peut causer des chocs électriques, un incendie et/ou des blessures graves. Dans l’utilisation des outils électriques, toujours suivre les consignes de sécurité pour minimiser les risques d’incendie, choc électrique et blessures corporelles.

  • Page 10: Consignes Particulières De Sécurité

    Entretenir l’outil avec soin. Garder les outils de coupe bien aiguisés et propres. Les outils entretenus correctement avec des lames bien aiguisées sont moins susceptibles de rester pris et sont plus faciles à contrôler. Vérifier que les pièces sont bien alignées et non bloquées, qu’il n’y a pas de pièces brisées ni aucun autre problème qui puisse nuire au bon fonctionnement de l’outil.

  • Page 11: Liste Des Composantes

    Replacer la pile. Le pistolet agrafeur CT50™ est maintenant prêt. point up 2 Pose d’agrafes. Le pistolet agrafeur sans fil CT50™ a une molette de réglage de la profondeur de pénétration de l’agrafe (Fig. 8). Changer d’un matériau souple à un matériau rigide est donc simple.

  • Page 12: Entretien

    3 Guide à LED. Un guide à LED est incorporé à l’avant du boîtier du CT50™ (Fig. 9). La diode électroluminescente s’allume lorsqu’on presse sur la gâchette. Au point de sortie de l’agrafe, le CT50™ est muni d’un dispositif de sécurité Fig. 10). qui empêche le pistolet agrafeur de partir lorsque le contact avec la surface de travail n’a pas été...

Table des Matières