Publicité
Les langues disponibles
Les langues disponibles
Stopping the machine
9.
Release the paddle (4, Fig. C).
10. Lift the brushes/pad-holder by means of the switch (2,
Fig. B).
NOTE
While the deck (12/15, Fig. C) is moving from
the lowered position to the lifted position, the
warning light on the switch (2, Fig. B) flashes;
when the deck has reached the lifted position,
the warning light turns off.
11. Lift the squeegee by means of the lever (25, Fig. C).
12. Make sure that the machine cannot move independently.
If equipped, engage the parking brake by pulling the
lever (34, Fig. C) until it locks.
MACHINE OPERATION (SCRUBBING/DRYING)
1.
Start the machine as described in the previous
paragraph.
2.
Keeping both hands on the handlebar (2, Fig. C),
manoeuvre the machine and start washing/drying the
floor.
3.
If necessary, vary the solution quantity to the brushes by
means of the lever (4, Fig. B).
4.
If necessary, adjust the squeegee balance adjusting
handwheel (18, Fig. C).
CAUTION!
To avoid any damage to the floor surface, stop
the brushes/pad-holder rotation when the
machine stops in one place, especially when
the machine is working with the extra pressure
function activated.
Working with brush/pad-holder extra pressure
function activated
5.
If the dirt on the floor proves to be particularly difficult to
clean, it is possible to work with an extra pressure of the
brushes/pad-holders on the floor by pressing the switch
(3, Fig. B).
CAUTION!
It is not possible to activate the extra pressure
function when the cylindrical brush-holder
deck (15, Fig. C) is used.
6.
To go back to normal pressure cleaning, press the switch
(3) again.
The switch (3, Fig. B) is active only when the deck (12,
Fig. C) is lowered and the warning light on the switch (2,
Fig. B) is on.
NOTE
While the deck (12, Fig. C) is moving, from the
lowered position with normal pressure to the
lowered position with extra pressure, the
warning light on the switch (3, Fig. B) flashes.
When the lowered position with extra pressure
is reached, the warning light stays on.
909 5319 000(3)2005-01 A
Brush overload safety system activation
7.
In case of brush motor overload, due to foreign bodies
which prevent the brushes/pad-holders from rotating, or
to excessively aggressive floors/brushes, the safety
system stops the brushes/pad-holders after about a
minute of continuous overload. The overload is shown
by the three warning lights (9a, 9b, 9c, Fig. B) flashing
simultaneously.
If the overload takes place during a cleaning with the
extra pressure function activated, the system
automatically reduces the pressure on the
brushes/pad-holders deactivating the extra pressure
function. If the overload persists, the
brushes/pad-holders stop.
8.
To start again after the brushes/pad-holders stop due to
overload, reset the machine by turning the ignition key
(10, Fig. B) to "0" position; then restart the machine by
turning the ignition key to "I" position.
Battery discharge during operation
9.
Until the green warning light (9a, Fig. B) stays on, the
batteries allow the machine to work normally.
When the green warning light (9a) turns off and first the
yellow warning light (9b) and then the red warning light
(9c) turn on, it is necessary to charge the battery,
because the machine residual autonomy of operation is
the following:
– When the yellow warning light (9b) turns on the
machine residual autonomy will last for a few
minutes (depending on the characteristics of the
battery).
– When the red warning light (9c) turns on the machine
autonomy is over: after a few seconds
brushes/pad-holders are automatically stopped and
the deck is automatically lifted; the squeegee
vacuuming and the machine drive still operate, just to
dry the wet floor and move the machine to the
charging area.
CAUTION!
Do not use the machine with discharged
batteries, to avoid damaging the batteries and
reducing the battery life.
NOTE
In case the machine drive cannot be used in
order to move the machine, see the
Pushing/Towing The Machine paragraph.
USER MANUAL
11
Publicité
Chapitres
Dépannage
