Cleaning, Maintenance And Ordering Of Spare Parts; Replacing The Power Cable; Carbon Brushes; Disposal And Recycling - Bavaria BPO 1100 E Mode D'emploi D'origine

Anleitung_BPO_1100_E_SPK1__ 03.01.14 12:18 Seite 12
GB
polishing (Fig. 8).
Make sure that the fleece attachment is free of all
n
foreign bodies.
Remove the layer of polish in the same order as it
n
was applied.
Important! Do not exert pressure on the
n
polishing machine!
Care tips
For optimum paintwork protection, you should
n
polish your car 2 to 3 times a year.
Wash your car at least every 2 weeks. Avoid
n
using household detergents as these can damage
the paintwork and remove the layer of wax.
Wash your car with a clean sponge, working from
n
top to bottom.
Remove all insects, bird droppings and tar stains
n
from the paintwork daily.
If you use any window-cleaning agents, spray
n
them onto a cloth and not directly onto the
windows in order to prevent them wetting the
paintwork.
6.2 Using as a sanding machine
Use the supplied sanding attachments (Fig. 9) for
sanding purposes.
The Velcro fastener enables easy changing of the
sanding attachments.
Place the whole surface area of the sanding disk
n
on the material.
Switch on the machine and move it with gentle
n
pressure over the workpiece completely circular
movements or moving it to and fro and up and
down.
Use a coarse paper for coarse sanding and a
n
finer paper for finish sanding. You can find the
best paper for the job by means of testing.
6.3 Speed Control Display: 10-30 (Fig. 2)
Use the speed control to set the desired working
speed.
Press the "+" button to increase the speed.
n
Press the "-" button to decrease the speed.
n
Refer to the display (8) for the set speed. Set speed
= Display x 100

7. Replacing the power cable

If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its after-
sales service or similarly trained personnel to avoid
danger.
12
8. Cleaning, maintenance and ordering
of spare parts
Always pull out the mains power plug before starting
any cleaning work.
8.1 Cleaning
Keep all safety devices, air vents and the motor
n
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
We recommend that you clean the device
n
immediately each time you have finished using it.
Clean the equipment regularly with a moist cloth
n
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts of
the equipment. Ensure that no water can seep
into the device.
Wash the polishing attachments only by hand and
n
let them air-dry. Use only a mild soap and a damp
cloth.

8.2 Carbon brushes

In case of excessive sparking, have the carbon
n
brushes checked only by a qualified electrician.
Important! The carbon brushes should not be rep
laced by anyone but a qualified electrician.
8.3 Maintenance
There are no parts inside the equipment which
n
require additional maintenance.
8.4 Ordering replacement parts
Please provide the following information on all orders
for spare parts:
Model/type of machine
n
Article number of the machine
n
ID number of the machine
n
Replacement part number of the required spare
n
part
For our latest prices and information please go to
www.isc-gmbh.info

9. Disposal and recycling

The unit is supplied in packaging to prevent its being
damaged in transit. This packaging is raw material
and can therefore be reused or can be returned to
the raw material system.
The unit and its accessories are made of various
types of material, such as metal and plastic.
Defective components must be disposed of as
special waste. Ask your dealer or your local council.