Bosch PST 700 E Notice Originale page 15

Check that the saw blade is seated securely. A loose
u
saw blade can fall out and lead to injuries.
Removing the saw blade (see figure B)
Push the saw blade receptacle (13) upwards in the direction
of the arrow and remove the saw blade (8).
If the saw blade jams during removal, press the saw blade re-
ceptacle (13) slightly forward (max. 2 mm).
Anti-splinter guard (see figure C)
The anti-splinter guard (14) (accessory) can prevent splin-
tering of the surface while sawing wood. The anti-splinter
guard can only be used with certain saw blade types and only
at a cutting angle of 0°. When sawing with the anti-splinter
guard, the base plate (5) must not be moved to the rear for
sawing close to edges.
Push the anti-splinter guard (14) into the base plate (5)
from below (as shown in the figure with the groove facing up-
wards).
Cut Control
Cut Control enables the power tool to be guided precisely
along a cutting line marked on the workpiece. Cut Control
includes the viewing window (9) with cut marks and the
base (10) for securing to the power tool.
Securing Cut Control to the base plate (see figure D)
Firmly insert the viewing window for Cut Control (9) into
the brackets on the base (10). Then push the base together
gently and allow it to click into place in the accessory holder
(15) on the base plate (5).
Dust/chip extraction
The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
– Use a dust extraction system that is suitable for the ma-
terial wherever possible.
– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
Connecting the dust extraction system
Connect a dust extraction hose (3) (accessory) to the ex-
traction outlet (4). Connect the dust extraction hose (3) to a
dust extractor (accessory).
You will find an overview of connecting to various dust ex-
tractors at the end of these operating instructions.
Bosch Power Tools
For optimum dust extraction, where possible use the anti-
splinter guard (14).
Switch off the sawdust blower device if you have connected
the dust extraction system (see "Sawdust blower device",
page 16).
The dust extractor must be suitable for the material being
worked.
When extracting dry dust that is especially detrimental to
health or carcinogenic, use a special dust extractor.
Operation
Operating modes
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Adjusting the mitre angle (see figures E–F)
The base plate (5) can be swivelled to the right or left to
make mitre cuts up to 45°.
The anti-splinter guard (14) cannot be used while mitre cuts
are being made.
– Insert a saw blade (8).
– Remove the anti-splinter guard (14).
– Loosen the screw (17) and push the base plate (5)
slightly towards the extraction outlet (4).
– The base plate has lock-in points at 0°, 22.5° and 45° on
the left and right so that the precise mitre angle can be
adjusted. Swivel the base plate (5) to the desired posi-
tion according to the scale (18). Other mitre angles can
be adjusted using a protractor.
– Then push the base plate (5) towards the saw blade (8)
as far as it will go.
– Slide the bracket (16) so that the guide roller (7) fits
against the back of the saw blade. Precise cuts are only
possible when the guide roller fits closely against the back
of the saw blade.
– Retighten the screw (17).
Cut Control for mitre cuts
(19) (9) (10) (5)
To enable you to track the cutting line (Cut Control), the
viewing window for Cut Control (9) has a mark (19) for
right-angled cuts at 0° and a mark (20) for rightward- and
leftward-slanting mitre cuts at 45° according to the scale
(18).
The cut mark for mitre angles between 0° and 45° is propor-
tional. It can also be marked on the viewing window for
English | 15
(20) (18)
1 609 92A 49Y | (18.09.2018)