Technical Characteristics; Installation And Put In Operating - Wallmek HPB Notice D'emploi


The operator will have to wear fit protective garments as required by the safety laws in force.

It is necessary to leave the pump away from excessive sources of heat or flames. Maximum environmental
temperature will never have to overcome 50° centigrade.

It's necessary disconnect the pressure before disconnecting pipings or hydraulic circuit connected.

In case of breakdown remove the feeding from the pump and contact the assistance.

No try in any case to tamper the settings planned by the builder.

Before beginning to work make sure that the machinery on which the pump is put in operating has EC conformity.

6. TECHNICAL CHARACTERISTICS

6.1 GENERAL CHARACTERISTICS.

The entry pressure can change from a minimum of 6 to a maximum of 10 Bar.

We suggest a pressure of feeding of 8 Bar (116 PSI).

The employment pressure can change according to the setting required by customer, by a minimum of 100 bar to a
maximum of 700 Bar.

In the model HPB, HPB WITH HAND CONTROL, HPB RC, the tank contains 1,3 Lt. of oil; in the model GHIBLI,
GHIBLI RC, GHIBLI TX the tank contains 2,5 Lt. of oil; and in the model SPH LT e SPH LT RC the tank contains
5 Lt. of oil. The oil tolerance of for any model of pumps ±0,1 Lt.

For periodical substitution it's necessary to use oil: (MOBIL DTE 11- SHELL TELLUS OIL T15-CASTROL
HYSPIN AWH15 or similar).

The standard air connection is 1/4" Gas.

The standard oil connection is 3/8" Gas

The standard flex, where supplied is mm 1.500 long the dimension of diameter is of 1/4"

The cable of remote control, in the RC model, is 3.000 mm long.

The Radio-control is fed with a battery a 9 Volt. We suggest (Super Pila GF22B TRANSISTOR 9 V. or similar).
6.2 SPECIFIC CHARACTERISTICS IN THE MODEL WITH RADIO-CONTROL

The model TX is constituted by 1 transmitter (Radio-control) and 1 receiver, or more receivers until a maximum of
4.

The receiver is installed on the pump.

The transmitter is already endowed with battery a 9 Volt.

The put in operating of the receiver is allowed by a rechargeable battery at 12 Volt installed on the carter.

The receiver gives impulses to 2 pneumatic electro-valves at 12 Volt (ON-OFF) that are normally closed. When the
receiver is in action a red led signals the operation. The receiver gains commands transmitted by the Radio control
and allows the operating of pumps.

The other constructive materials and the other particulars of which is composed the pump are similar to which of
GHIBLI model as well as the function of every piece.

A switch is placed on the Carter for the pump lighting, one as well as a bright signaller that points out the charge of
battery . The special battery charger at 220 Volt allows the recharging when this is necessary. If required the battery
charger can be furnished with a 110 Volt voltage.
7. INSTALLATION AND PUT OPERATING
The pump must be put on the floor in horizontal position. The hand pump can be placed on the workbench or on suitable
surfaces for a confortable
stirrups. The pump is already furnished complete of oil.
A) CONNECTION TO THE COMPRESSED AIR.
Before connecting the discharge pipe verify that the feeding air (8 bar-116 PSI) comes from a filter regulator endowed
with slingers (to guarantee lubricated air with no impurity) It's necessary to use a coupling which is good for the
apparatus in equipment. To guarantee an air opportunity dry, we suggest the dessictor employment on the air compressed
system; such shrewdness will make the performance of the hydraulic pumps and any other pneumatic equipment longer.
B) OIL CONNECTIONS.
The connection between pump and the use must have realized with flexible pipes and fit couplings to bear the nominal
pressure multiplied by 3. It is advised to wind the fillets with ribbon Teflon. Make sure, in case of use of ribbon Teflon,
that this doesn't obstruct the oil passage. Tighten with care the connections and make sure that engagements are correctly
inserted.
C) VENT PLUG.
In the HPB-HPB WITH HAND CONTROL-GHIBLI-GHIBLI RC-GHIBLI TX-SPH LT- SPH LT RC replace the
hermetic plug, with that special composed by a rod, so that it will be the possible check the oil level. This special plug is
work. The RC and TX models can be installed in elevated horizontal position using its special
13