Télécharger Imprimer la page

Publicité

Liens rapides

Precaution
• This unit is designed for negative ground 12 V DC
operation only.
• Avoid installing the unit where:
— it would be subject to high temperatures such as
from direct sunlight or hot air from the heater.
— it would be exposed to rain or moisture.
— it would be subject to dust or dirt.
• If the unit is placed too close to the car radio, the TV
tuner or the antenna interference may occur. In this
case, separate the unit from the car radio, TV tuner
or the antenna.
• For safety reasons, keep your car audio volume
moderate so that you can still hear sounds outside
your car.
• A special setting tool is required to set the cross-
over network and parametric equalizer of the XDP-
4000X. Consult your nearest Sony dealer for further
information about the installation, connections, and
settings.
• To use the XDP-4000X, you will need a Sony master
unit with the DSP control function.
• If you connect a master unit with voice guide to this
unit, the voice guide function will not work.
If you have any questions or problems concerning
your unit that are not covered in this manual, please
consult your nearest Sony dealer.
Notes in operation
• Operating the MUTE (ATT) function on the unit is
different from operating the function on the master
unit. On this unit, when MUTE (ATT) is ON, the
volume setting function cannot be operated; this is
not a malfunction. The MUTE (ATT) function is not
overridden by the volume function.
• Two units can not be used at same time.
Installation
Before installation
• Choose the mounting location carefully so that the
unit will not interfere with the normal driving
functions of the driver.
• Mount the unit either under a seat or inside the
trunk space.
• For models which have a sound input/output
switch on the master unit, be sure to put the switch
in the 2 position (sound input position).
• You can register up to 10 presettings on the
XDP-4000X of the cross-over network and
parametric equalizer for the best sound results
suitable to your car interior. In this case, if you
connect the XDP-4000X to a master unit, the Bass/
Treble and Balance/Fader functions on the master
unit are disabled so that these presettings will not
be disturbed. (Consult your nearest Sony dealer for
further information about each presetting.)
• Connect the power cord of the XDP-4000X
directly from the battery to the amplifier. Make
sure to insert a 5A fuse as close as possible to
the battery.
If you make a connection without
using a fuse, or otherwise make some
mistake in the wiring, the cable could burn
through.
Installing with the
supplied screws
Prepare a sound mounting board with enough
thickness (more than 14 mm (9/16 in.)) to install the
unit securely.
Place the unit directly onto the mounting board and mark the four bolt holes, then drill the holes
1
(3 mm (1/8 in.) dia.).
Fixez l'appareil directement sur la plaque de montage, tracez la position des quatre orifices de
vissage et percez les trous (3 mm diam. (1/8 pouces)).
Mounting board (Not supplied)
Plaque de montage (non fournie)
2
Secure the unit to the board with the
supplied screws.
Fixez l'appareil sur la plaque à l'aide des
vis fournies.
After installation and
connection
Make sure that the POWER indicator of the unit
lights up when you turn on the master unit.
Précautions
• Cet appareil est conçu pour fonctionner avec une
liaison à la masse négative de 12 V CC uniquement.
• Evitez d'installer l'appareil dans des endroits où il
serait soumis à :
— des températures élevées comme sous le
rayonnement direct du soleil ou l'air chaud du
chauffage;
— la pluie ou à de l'humidité;
— la poussière ou à la saleté.
• Si l'appareil est placé trop près de l'autoradio, du
syntoniseur TV ou de l'antenne, des interférences
risquent de se produire. Dans ce cas, éloignez
l'appareil de l'autoradio, du syntoniseur TV ou de
l'antenne.
• Pour des raisons de sécurité, gardez le volume de
votre installation audio de voiture à un niveau
modéré de façon à ce que vous puissiez entendre
les bruits de la circulation.
• Un outil de réglage spécial est indispensable pour
régler le circuit de recoupement et l'égaliseur
paramétrique du XDP-4000X. Consultez votre
revendeur Sony pour des informations plus détaillées
sur l'installation, le raccordement et les réglages.
• Pour utiliser le XDP-4000X, vous avez besoin d'un
appareil principal Sony doté de la fonction de
commande DSP.
• Si vous raccordez à cette unité un appareil principal
doté de la fonction de guide vocal, la fonction de
guide vocal sera inopérante.
Si vous avez des questions ou des problèmes
concernant votre appareil qui ne sont pas abordés
dans le présent mode d'emploi, consultez votre
revendeur Sony.
Remarques sur le fonctionnement
• Le fonctionnement de la fonction MUTE (ATT) est
différent sur l'unité et sur l'appareil principal. Sur
cette unité, lorsque MUTE (ATT) est réglé sur ON, la
fonction de réglage du volume ne peut être actionnée;
il ne s'agit pas d'un dysfonctionnement. La fonction
MUTE (ATT) n'est pas supplantée par la fonction de
volume.
• Il n'est pas possible d'utiliser deux appareils en même
temps.
Installation
Avant l'installation
• Choisissez soigneusement l'endroit de montage de
façon à ce que l'appareil n'interfère pas avec les
manoeuvres normales de la conduite d'une voiture.
• Installez l'appareil sous un siège ou dans la malle
arrière.
• Dans le cas des modèles équipés d'un commutateur
d'entrée/sortie audio sur l'appareil principal,
veillez à régler le commutateur sur la position 2
(position d'entrée audio).
• Vous pouvez enregistrer jusqu'à 10 présélections
sur le XDP-4000X du circuit de recoupement et
l'égaliseur paramétrique pour obtenir les meilleurs
résultats acoustiques en fonction de l'habitacle de
votre voiture. Dans ce cas, si vous raccordez le
XDP-4000X à un appareil principal, les fonctions
Bass/Treble et Balance/Fader de l'appareil
principal sont désactivées de façon à ce que ces
présélections ne soient pas perturbées. (Consultez
votre revendeur Sony pour des informations plus
détaillées sur chacune de ces présélections.)
Branchez directement le cordon
d'alimentation du XDP-4000X de la batterie à
l'amplificateur. Installez un fusible de 5A le
plus près possible de la batterie. Si vous
établissez une connexion sans fusible, ou si
vous commettez une erreur de câblage, le
câble risque de brûler.
Installation à l'aide des
vis fournies
Préparez une robuste plaque de montage d'une
épaisseur suffisante (plus de 14 mm (9/16 pouces))
pour y installer correctement l'appareil.
3 mm dia.
3 mm diam.
m m m m m
1
Après l'installation et le
raccordement
Assurez-vous que l'indicateur POWER de l'appareil
s'allume lorsque vous mettez l'appareil principal
sous tension.
POWER indicator
Indicateur POWER
Digital
Preamplifier
Operating Instrunctions
Mode d'emploi
Owner's Record
The model and serial numbers are located on the bottom of the unit.
Record the serial number in the space provided below.
Refer to these numbers whenever you call upon your Sony dealer regarding this product.
Model No. XDP-4000X Serial No.
XDP-4000X
Sony Corporation ©1998
For the customers in the USA
Warning
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates, uses, and can radiate radio
frequency energy and, if not installed and used
in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is
encouraged to try to correct the interference by
one or more of the following measures:
Parts for installation and
connections
1
2
× 4
Specifications
Power requirements
12 V DC car battery (negative
ground, 10.5 V — 16 V)
Current drain
1 A
Frequency response
5 Hz — 20 kHz
Signal-to-noise ratio
105 dB (Optical input)
Harmonic distortion
0.003 % (Optical input)
Separation
95 dB at 1 kHz
Input/output terminals
BUS input (1)
BUS output (1)
Line input (RCA jack) (2)
Line output (RCA jack) (4)
Optical digital input (2)
Approx. 249 × 45 × 183 mm
Dimensions
× 7
× 1
(9
7
/
1
/
13
/
in.)
8
4
16
(w/h/d)
Mass
Approx. 2 kg (4 lb. 7 oz.)
Optional accessories
BUS cable (supplied with RCA
pin cord) RC-61 (1 m), RC-62
(2 m)
Optical cable RC-97 (2 m)
Optional equipment
Master unit (which can
operate a digital preamplifier)
CDX-C90/C90R, CDX-C910/
C910RDS, MDX-C8900,
XR-C9100/C9100RDS etc.
CD changer
CDX-91, CDX-805 (equipped
with a digital output)
CDX-T65, CDX-715, CDX-T62
etc.
MD changer
MDX-62
Source selector (compatible
with an analog system)
XA-C30
TV tuner (USA model only)
XT-40V etc.
Power amplifier
XM- Series
Speakers
XS- Series
Note
If you connect this unit to the XDP-U50D or the XDP-
210EQ, this unit will not work.
Design and specifications subject to change without
notice.
Printed in Japan
— Reorient or relocate the receiving antenna.
— Increase the separation between the
equipment and receiver.
— Consult the dealer or an experienced radio/
TV technician for help.
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate
this equipment.
Pièces d'installation et de
raccordement
3
(2 m)
Spécifications
Puissance de raccordement Batterie de voiture 12 V CC
(masse négative, 10,5 V — 16 V)
Consommation de courant
1 A
Réponse en fréquence
5 Hz — 20 kHz
Rapport signal-bruit
105 dB (Entrée optique)
Distorsion harmonique
0,003 %
Séparation
95 dB à 1 kHz
Bornes d'entrée/sortie
Entrée BUS (1)
Sortie BUS (1)
Entrée de ligne (prise RCA) (2)
Sortie de ligne (prise RCA) (4)
Entrée optique numérique (2)
Approx. 249 × 45 × 183 mm
Dimensions
× 7
× 1
(9
7
/
1
/
13
/
pouces)
8
4
16
(l/h/p)
Masse
Approx. 2 kg (4 lb. 7 oz.)
Accessoires en option
Câble BUS (fourni avec un
cordon à broche RCA) RC-61
(1 m), RC-62 (2 m)
Câble optique RC-97 (2 m)
Appareil en option
Appareil principal (pouvant
commander un
préamplificateur numérique)
CDX-C90/C90R, CDX-C910/
C910RDS, MDX-C8900,
XR-C9100/C9100RDS etc.
Changeur CD
CDX-91, CDX-805 (doté d'une
sortie numérique)
CDX-T65, CDX-715, CDX-T62 etc.
Changeur MD
MDX-62
Sélecteur de source
(compatible avec un système
analogique)
XA-C30
Syntoniseur de télévision
(modèle pour les USA
uniquement) XT-40V etc.
Amplificateur de puissance
Série XM-
Haut-parleurs
Série XS-
Remarque
Si vous raccordez cet appareil à un XDP-U50D ou un
XDP-210EQ, cet appareil sera inopérant.
La conception et les spécifications sont sujettes à
modifications sans préavis.
*I-3-864-854-11*
(2)

Publicité

loading

Sommaire des Matières pour Sony XDP-4000X

  • Page 1 DSP. your unit that are not covered in this manual, please Refer to these numbers whenever you call upon your Sony dealer regarding this product. • Si vous raccordez à cette unité un appareil principal consult your nearest Sony dealer.
  • Page 2 Listening to each Utilisation de cet Ecoute d’une source program source in its appareil programme avec sa You can control this unit from a Sony DSP controlled Master unit. registered equalizer courbe d’égaliseur Vous pouvez exploiter cet appareil au départ Note d’une unité...
  • Page 3 LINE OUT BUS CONTROL IN If you need some extra connecting cables or cords, you can find them in the Sony audio accessory lineup. For the equipment to be connected to the unit, refer to “Optional equipment.” Si vous avez besoin de câbles ou de cordons de connexion supplémentaires, vous les trouverez dans la gamme d’accessoires audio Sony.
  • Page 4 With several CD/MD changers (analog) With a TV tuner (USA model only) Avec plusieurs changeurs CD/MD (analogiques) Avec un syntoniseur de télévision (modèle pour les USA uniquement) ANALOG ANALOG LINE OUT ANALOG IN DIGITAL IN BUS CONTROL POWER CHANGER MASTER CHANGER MASTER CHANGER...