Using Your Cleaner; Cleaner Maintenance - Hoover Telios TE70TE12 Manuel D'utilisation

GETTING TO kNOw yOUR ClEANER
A. Cleaner main body
B. On/Off Button
C. Cord Rewind Button
D. Variable Power Control*
E. Bag Check Indicator
F. Bag Door Release Latch
G. Bag Door
H. Pre-motor Filter
I. Exhaust Filter
J. Exhaust Filter Cover
K. Accessories door
L. Hose Handle
M. suction Regulator*
N. Hose
ASSEmBlING yOUR ClEANER
Remove all components from the packaging.
1. Connect the hose to the cleaner main body, ensuring it clips and locks into position. To
release the hose: simply press the two latches on the hose end and pull. [2]
2. Connect the handle to the upper tube end. [3]
3. Connect the tube lower end to the carpet and floor nozzle**. [4]

USING yOUR ClEANER

1. Extract Power Cord and plug it into the power supply. Do not pull the cord beyond the
red marker. [5]
2. Adjust the Telescopic Tube* to the desired height by moving the Telescopic Tube
Adjusters* up and raise or lower the handle to the most comfortable cleaning position. [6]
3. Carpet and Floor Nozzle**: Press the floor type selector pedal on the nozzle [7] to select
the ideal cleaning mode for the floor type.
Hard Floor – Brushes are lowered to protect the floor.
Carpet – Brushes are raised for the deepest clean.
4. switch the cleaner on by pressing the On/Off button on the cleaner main body. [8]
5. slide the Variable Power Control* to increase or decrease the suction. [9]
6. Adjust the suction regulator* to the desired level. [10]
7. switch off at the end of use by pressing the On/Off button. Unplug and press the Cord
Rewind Button to wind the power cord back into the cleaner. [11]
8. Parking and storage - The tube can be parked for temporary storage [12] while in use,
or in the storage position when not in use. [13]
*Certain models Only ** Certain models only, nozzles may vary according to model
O. Telescopic Tube*
P. Telescopic Tube Adjuster*
Q. Carpet and Floor nozzle(GP)**
Q1. Carpet Nozzle (CA)**
Q2. Hard Floor Nozzle (HF)**
R. Floor type selector
s. Crevice Tool
T. Furniture Nozzle
U. Dusting Brush
V. Pet Hair Remover Mini Turbo Nozzle*
W. Allergy Remover Mini Turbo Nozzle*
X. Grand Turbo Nozzle*
Y. Hard Floor Caresse Nozzle*

ClEANER mAINTENANCE

Replacing the Dust Bag
If the Bag Check Indicator is illuminated please check and if necessary, replace the dust bag.
1. Lift the bag door release latch [14] to open the bag door, close the bag to avoid dust
escaping by pulling the tongue and remove the bag. [15]. The full dust bag should be
disposed of correctly and carefully.
2. Fold a new bag as shown on the bag and fit by inserting the collar into the bag holder [16].
3. Close the bag door.
Remember: The bag check indicator may be red if an obstruction has occurred. In this
case, refer to 'Removing a Blockage From the system' .
Cleaning the Filter
To maintain optimum performance of your cleaner, please wash the pre-motor filter and
exhaust filter after each 5 bag changes.
Cleaning the pre-motor filter:
1. Lift the Bag Door Release latch [14] to open the bag door and remove the bag. [15]
2. To remove the pre-motor filter slide the pre-motor filter frame from the cleaner. [17]
3. Remove the filter from the holder. [18]
4. Wash it in hand warm water, [19] and allow it to dry thoroughly before replacing it in
the cleaner.
Cleaning the exhaust filter:
1. To remove the exhaust filter, unclip the exhaust filter cover [20] and remove the
exhaust filter pack. [21]
2. Wash the filter in hand warm water [19] and allow it to dry thoroughly before replacing
in the cleaner.
REmEmBER: Do not use hot water or detergents. In the unlikely event of the filters
becoming damaged, fit a genuine Hoover replacement. Do not try and use the product
without a dust bag or filter fitted.
Cleaning the permanent cloth dust bag* :
To maintain optimum performance we recommend that you wash the permanent cloth
dust bag under hand warm water after every 5 full bags. Remove excess water and leave
to dry fully before replacing.
Removing a Blockage From The System
If the Bag Check Indicator is red:
1. Check if the bag is full. If so refer to 'Replacing The Dust Bag' .
2. If is not full, then;
A. Do the filters need cleaning? If so refer to 'Cleaning the Filter' .
B. Check if there is any other blockage in the system - Use a rod or a pole to remove
any blockage from Telescopic Tube or flexible hose.
warning* : The bag check indicator will remain illuminated if the cleaner is used when
2
GB