Setting Up And Assembly - Thomashilfen EASyS Manuel De L'utilisateur

EASyS Modular seating system
Seat depth
Seat width
Back height *
Lower leg length
Hip angle
Knee angle
Foot angle
Turning range of seat
Seat tilt-in-space (on A chassis)
Height adjustment arm support
Size of arm support (w x h)
Size of foot rest (w x d)
Overall dimensions (l x w x h)
Folded dimensions (l x w x h)
Weight (seat) *
Carrying capacity (seat)
* without headrest

Setting up and assembly

Adjustments / adaptations shall be carried out by trained or instructed experts (e.g. medical device consultants of a medical device
dealer) only.
The seat can be removed from the A chassis without needing any tools. Push the click lever below the seat unit forwards and take
the seat unit off the receiver adapter of the chassis forwards. Proceed in reverse order to insert the seat.
CAUTION: Always ensure the click lever engages audibly. Then make sure the seat has clicked into place by pulling it
forwards.
Commercially available tools are required for mounting / dismounting the accessories. Separate mounting instructions and user
manuals are enclosed with the accessories. If they should be missing, you can download the instructions in the download section
of our website www.thomashilfen.com
Mounting the foot rest
The foot rest is to be fixed to the knee joints. Place the grid joints one upon the other and connect them with the screws (from the
inside), washers (from the outside), and wing nuts (from the outside). (Fig. 1)
Lateral backrest upholstery / side upholstery (EASyS)
Put the lateral backrest upholstery over the lateral tube and velcro it left and right to the curved section of the back plate (the snap
fastener points inwards). Close the Velcro of the lateral backrest upholstery completely. Attach the lateral upholstery to the lateral
backrest upholstery with the snap fastener. In addition, velcro it to the back plate. (Fig. 2-4)
Lateral backrest upholstery (EASyS Modular)
Put the lateral backrest upholstery over the lateral tube and velcro it left and right to the curved section of the back plate. Close the
Velcro completely – also over the knurled screw. In addition, velcro it to the back plate. (Fig. 5-6)
Receiver for sun and rain cover
Both EASyS and EASyS Modular are equipped with receivers for the sun and rain cover. (Fig. 7)
Seat upholstery
Velcro the seat upholstery to the seat plate. (EASyS only: Fix the two lower Velcro fasteners around the tubes of the foot rest).
Inserting the seat unit
Place the seat unit on the rear crossbar and move the seat forward and down. The EASyS click system engages automatically and
audibly. (Fig. 8)
Removal of the seat unit
To remove the seat unit, push the click-lever under the seat forward and take the seat unit off the chassis forward. (Fig. 8)
EASyS Modular Size 1
16 - 28 cm / 6.3 - 11"
20 - 30 cm / 7.9 - 11.8"
26 - 42 cm / 10.2 - 16.5"
17 - 30 cm / 6.7 - 11.8"
90° to 140°
90° to 180°
78° to 100°
180°
-10 to + 35°
10 - 14 cm / 3.9 - 5.5"
21 x 10 cm / 8.3 x 3.9"
29 x 18 cm / 11.4 x 7.1"
85 x 41 x 57 cm
33.5 x 16.1 x 22.4"
89 x 41 x 38 cm
35 x 16.1 x 15"
7.9 kg / 17.4 Ib
35 kg / 77.2 Ib
EASyS Modular Size 2
24 - 35 cm / 9.4 - 13.8"
26 - 35 cm / 10.2 - 13.8"
32 - 52 cm / 12.6 - 20.5"
25 - 36 cm / 9.8 - 14.2"
90° to 140°
90° to 180°
78° to 100°
180°
-10° to +35°
12 - 18 cm / 4.7 - 7.1"
29 x 12 cm / 11.4 x 4.7"
33 x 21 cm / 13 x 8.3"
64 x 48 x 77 cm
25.2 x 18.9 x 30.3"
90 x 48 x 60 cm
35.4 x 18.9 x 23.6"
9.6 kg / 21.2 Ib
40 kg / 88.2 Ib
15